Data-Tronix DT-UPS-1000-SMOL Скачать руководство пользователя | Manualshive

Страница: 7 / 41

background image

7

6. Charger: The charger of standard UPS provides 1A charging current; and

long backup time provided 5.5A charging current.

7. Battery: Sealed maintenance-free lead –acid battery can be used as the DC

source of the UPS.

8. Output filter: It filters the output and provides clean AC power to the load.

3 Installation

3. 1 Unpacking Inspection

1. Open the packing box of UPS and take it out, visually examine the unit for

transit damage.

2. Check against the accessory lists that the accessories of the UPS are present.

(Refer to Table 9-1).

3. Make sure the model is what you wanted from the nameplate on the rear

panel

4. If the UPS arrives damaged, or there is any missing accessory or other

question above, please contact the distributor immediately.

3. 2 Installation Notes

1. When locating the UPS, make sure there is no hazardous objects such as

water, inflammable gas, corrosive agents and so on around the UPS, and that

the installation environment meets the specifications.

«
...
5
6
7
8
9
...
»

Содержание DT-UPS-1000-SMOL










































Отзывы:

Нет отзывов

Похожие инструкции для DT-UPS-1000-SMOL

Minuteman Enspire Series

Бренд: Para systems Страницы: 19

Бренд: JALpower Страницы: 31

NetPower NPW 1000

Бренд: Riello UPS Страницы: 6

Бренд: OPTI-UPS Страницы: 51

Бренд: FSP Technology Страницы: 39

Бренд: Groups Страницы: 31

Бренд: LEGRAND Страницы: 2

Бренд: LEGRAND Страницы: 4

Daker DK 10 kVA

Бренд: LEGRAND Страницы: 16

DAKER DK Plus Series

Бренд: LEGRAND Страницы: 28

PowerWave 9000DPA S2

Бренд: Kohler Страницы: 67

NUMERIC Onfiniti

Бренд: LEGRAND Страницы: 17

NUMERIC 1 kVA FM

Бренд: LEGRAND Страницы: 27

UPS MepRT II -1000

Бренд: LESTAR Страницы: 2

POWER Plus Premium SA 15

Бренд: Gamatronic Страницы: 71

SG800-1, SG800-2 SG1K-1T, SG1K-2T SG2K-1T

Бренд: Falcon Страницы: 8

Бренд: Xtreme Power Conversion Страницы: 9

Бренд: Eaton Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды