Data-Tronix DT-UPS-1000-SMOL Скачать руководство пользователя

Страница: 35 / 41

7 Troubleshooting

Faults

Possible

cause

Solution

Fault/Warning

code

Fault icon

Alarm

F01

constantly

Beep

continuously

Internal

fault.

Please

contact

the

distributor or Service center

F02

constantly

Beep

continuously

Internal

fault.

Please

contact

the

distributor or Service center

F03

constantly

Beep

continuously

Internal

fault.

Please

contact

the

distributor or Service center

F04

constantly

Beep

continuously

The UPS

output is

short

circuited

Turn  off  the  UPS.  Remove
all  loads.  Ensure  that  the
loads  are  not  failed  or  the
UPS  has  no  internal  short
before  turn  on  it  again.  If
failed,  please  contact  the
distributor or service center

F05

constantly

Beep

continuously

Internal

fault.

Please

contact

the

distributor or Service center

F06

constantly

Beep

continuously

Internal

fault.

Please

contact

the

distributor or Service center

F07

constantly

Beep

continuously

Overload

fault

Reduce the member of
loads connected to the UPS.

F08

constantly

Beep

continuously

Internal

overheat

Ensure that the UPS is not
overloaded

and

the

ventilation opening is not
blocked

and

ambient

temperature  is  not  too  high.
Wait  for  10  minutes  for  the
UPS  to  cool  down  before
turning  it  on  again.  If  it
does

not

work.

Please

contact the distributor or
service center.

F09

constantly

Beep

continuously

The charger
of the UPS
is defective

Please

contact

the

distributor or Service center

A01

Blink once
every
second

Beep once

every second

Overload
pre-warning

Reduce the member of
loads connected to the UPS.

Содержание DT-UPS-1000-SMOL










































Результаты поиска

Содержание DT-UPS-1000-SMOL

Отзывы:

Похожие инструкции для DT-UPS-1000-SMOL

Бренды по названию

Популярные бренды

Data-Tronix DT-UPS-1000-SMOL, Руководство пользователя

Результаты поиска

Содержание DT-UPS-1000-SMOL

Отзывы:

Похожие инструкции для DT-UPS-1000-SMOL

Бренды по названию

Популярные бренды