Data Translation DT9816 Series Скачать руководство пользователя | Manualshive

Страница: 60 / 108

background image

Chapter 5

60

Specifying One or More Analog Input Channels

You can read data from one or more analog input channels using an analog input channel list
and continuous scan mode.

Using software, specify the channels you want to sample. You can enter up to six entries in the
channel list for this module. Group the channels in the list sequentially (starting either with 0
or with any other analog input channel) in ascending order. You cannot specify the same
channel more than once in the list.

Refer to

for more information about continuous scan mode.

Input Ranges and Gains

DT9816 Series modules provide an input range of ±10 V. Use software to specify the range as
±10 V with a gain of 1 for an effective range of ±10 V, or specify a gain of 2 for an effective
input range of ±5 V.

Note:

You must set the gain to the same value for all channels, even if you are using a subset

of the channels.

Input Sample Clock Sources

DT9816 Series modules allow you to use one of the following clock sources to pace analog
input operations in continuous mode:

• The internal A/D sample clock

• An external A/D sample clock

The following subsections describe the internal and external A/D sample clocks in more
detail.

Internal A/D Sample Clock

You can pace an analog input operation on a DT9816 Series module using an internal clock
source. Using software, specify the clock source as internal, and then specify the clock
frequency at which to pace the operation. The supported frequencies depend on the model
you selected, as shown in

Table 5: Supported Clock Frequency

Model

Minimum Frequency

Maximum Frequency

DT9816 and DT9816-OEM

60 Hz

50 kHz

DT9816-A

60 Hz

153.846 kHz

DT9816-S and DT9816-S-WTR

183.1 Hz

750 kHz

«
...
58
59
60
61
62
...
»

Содержание DT9816 Series













































































































Отзывы:

Нет отзывов

Похожие инструкции для DT9816 Series

Бренд: jbc Страницы: 4

Бренд: EA Страницы: 24

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренд: FAAC Страницы: 16

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: Fingertips Lab Страницы: 15

Бренд: Dantherm Страницы: 20

Бренд: Parker Страницы: 38

Бренд: Parker Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды