Data Translation DT7837 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 98

Data Translation DT7837 Скачать руководство пользователя страница 61

Specifications

61

DC Accuracy

Offset error

d

±1 mV

Offset error temperature coefficient

±(7.2

μ

V/

°

C )/ Gain) ± 100

μ

V/

°

C

Gain error

Gain of 1:
Gain of 10:

±0.02%
±0.5%

Gain error temperature coefficient

50 ppm/

°

C

ADC Integral Non-Linearity error, INL

±0.0006% of full-scale range

ADC Differential Non-Linearity error, DNL

Monotonic to 24 bits

Dynamic Performance

e

Gain of 1

Gain of 10

Effective Number of Bits, ENOB

f

(1 kHz input, 105.5 kSPS)

–1 dBFS input:
–6 dBFS input:

15 bits
16 bits

15 bits
16 bits

Signal to Noise and Distortion Ratio, SINAD

g

(1 kHz input, 105.5 kSPS)

–1 dBFS input:
–6 dBFS input:

93 dB
92 dB

93 dB
92 dB

Signal to Noise Ratio, SNR

h

(1 kHz input, 105.5 kSPS)

–1 dBFS input:
–6 dBFS input:

97 dB
96 dB

97 dB
96 dB

Total Harmonic Distortion, THD

i

(1 kHz input, 105.5 kSPS)

–1 dBFS input:
–6 dBFS input:

–102 dB
–100 dB

–102 dB
–101 dB

Spurious Free Dynamic Range, SFDR

j

(1 kHz input, 105.5 kSPS)

–1 dBFS input:
–6 dBFS input:

97 dBFS
103 dBFS

98 dBFS
102 dBFS

Noise Floor
(50

Ω

input termination, 105.5 kSPS)

56

μ

VRMS

65

μ

VRMS

Overvoltage Protection

Overvoltage protection

Power on:
Power off:

+40 V to –20 V
±40 V

ESD protection

Arc:
Contact:

8 kV
4 kV

a.  The total frequency response is the combined frequency response of the ADC Delta Sigma filter and the analog filter.
b.  Channel 0 is the reference channel with a 20 Vpp signal and a maximum sample rate of 105.469 kSamples/s.
c.  Cable capacitance of 30 pF per foot (typical) must be added.
d.  Offset errors are referred to the input.

Table 4: Analog Input Subsystem Specifications (cont.)

Feature

DT7837 Specifications

«
...
59
60
61
62
63
...
»

Содержание DT7837



































































































Отзывы:

Нет отзывов