Data Translation DT7837 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 98

Data Translation DT7837 Скачать руководство пользователя страница 13

Overview

13

• USB 2.0 host connection to external devices, such as a mouse, keyboard, or external

storage devices.

• Analog input subsystem:

−

Four, single-ended analog input channels available through SMA connectors.

−

Four simultaneous sampling, Delta-Sigma, 24-bit analog-to-digital converters (ADCs).

−

Support for IEPE (Integrated Electronic Piezoelectric) inputs, including use of a 4 mA
current source with 20 V compliance voltage for AC or DC coupling.

−

Programmable throughput rate from 195.3125 Samples/s to 105.469 kSamples/s.

−

Input range of ±10 V with software-selectable gains of 1 and 10 for an effective input
range of ±10 V and ±1 V.

−

Continuous acquisition from multiple analog input channels simultaneously.

−

Supports the ability to return the value of the tachometer, general-purpose
counter/timer, measure counter, and/or digital input port in the analog input data
stream, allowing you to measure a variety of signals synchronously with analog input
measurements.

−

Software-programmable trigger source (software trigger, external trigger, or threshold
trigger using any analog input channel) to start acquisition.

−

Accounts for analog input group delay in hardware and allows user-specified trigger
delay to account for analog output group delay.

• Up to eight, TTL digital input lines using the eight general-purpose inputs. You can read

the digital input port directly or you can return the value of the digital input port in the
input data stream.

• Up to eight, TTL digital output lines using the eight general-purpose outputs. You can

write a value to the digital output port directly.

• One, 32-bit, general-purpose counter/timer for performing event counting, rate

generation, and non-repeatable one-shot operations. You can use two general-purpose
input signals for the C/T clock and gate inputs and one general-purpose output signal for
the C/T clock output. You can read the value of the counter/timer directly or through the
input data stream.

• One tachometer input signal. The value of the tachometer input signal can be returned in

the input stream.

• One phase/measure counter. You can program the edge that starts the measurement and

the edge that stops the measurement. Many edge types are supported. The data from the
measure counter can be returned in the input stream.

• 2 GB embedded NAND flash memory that contains the Linux kernel, bootloader, and file

system; this memory can also be used to store user files and data

• 512 MB SDRAM (DDR3) memory

• 8 kBytes EEPROM

• Micro SD connector supports micro SD cards, which can be used as a boot source for

general-purpose file and data storage

• 3.3 V UART, I2C, and an SPI (Serial Peripheral Interface) interfaces for embedded

connectivity.

«
...
11
12
13
14
15
...
»

Содержание DT7837



































































































Отзывы:

Нет отзывов