manualshive.com logo in svg

Data Translation DT7837, Руководство пользователя, Страница: 25 / 98

Поделиться
Скачать
Data Translation DT7837 Скачать руководство пользователя страница 25

Principles of Operation

25

ARM Block

The ARM block of the DT7837 module uses the TI Sitara AM3352 processor and its associated 
peripherals to provide an open-source, single-board computer. The AM3352 supports many 
different interfaces, many of which are shared on the configurable I/O pins. In addition to the 
AM3352, the DT7837 module uses an embedded NAND flash and an FPGA. 

This section describes the features of the ARM block in more detail.

ARM Processor

The AM3352 is based on the ARM Cortex-8 32-bit processor and is configured to run at 
600 MHz.

Refer to the following web site for more information on this processor: 
http://www.ti.com/product/am3352

Memory

A 512 MB, DDR3, SDRAM memory device is connected to the AM3352 processor through a 
dedicated DDR (Double Data Rate) memory interface.

Embedded NAND Flash

A 2 GB embedded NAND flash device is connected to the AM3352 processor through the 
16-bit GPMC (General Purpose Memory Controller) bus, and can be accessed at the CS0 
address space. The flash memory contains the Linux kernel, bootloader, and the file system. 

You can also use the flash memory for general-purpose data and file storage as well as for 
input data and waveform storage.

EEPROM 

An 8 kByte EEPROM device is connected to the I2C0, 2-wire, serial interface of the AM3352 
processor. The EEPROM stores information about the device, including the calibration 
information. 

Содержание DT7837



































































































Отзывы:

Нет отзывов