Data Aire gForce Ultra Скачать руководство пользователя страница 29

Страница: 29 / 64

3.12 Manual Override Switches
For testing and during start-up each gForce Ultra unit is provided with manual override slide switches.

There are seven (7) slide switches. One for each of the following functions:

Water Valve

Fan Speed

Humidifier

Heat 1

Cool 2

Cool 1

Blower

All automatic control is disabled but the safety switches remain functional. Simply slide the manual

switches to energize the fan, compressor(s), humidification, reheat and other functions (as appli

cable).
The fan speed of the Electronically Commutated (EC) plug fan motor can be adjusted from 0 to 10

volts DC by adjusting the potentiometer at the left of the Fan Speed switch. The fan speed will in

crease 10% of the fan base speed for each one (1) volt adjustment (e.g., one (1) volt equals 10%

speed). At ten (10) volts the motor is at full speed.

WARNING:

Do not leave the unit in manual override. Slide the switches to

the OFF position when completing testing and/or start-up. An alarm will be

activated if units are left in the ON position.

3.13 Wiring Diagrams

Every Data Aire evaporator, condenser, condensing unit or fluid cooler comes with a wiring diagram.

These diagrams are ladder type schematics intended for service personnel. The intent is to allow the

technician to understand the wiring details associated with the electrical components and how they

interface with the controls as well as peripheral equipment (including secondary heat exchangers).
The wiring diagram in the evaporator will indicate field interface terminals to the secondary heat ex

changer

. The internal wiring of the secondary heat exchanger is found on a separate diagram which

can be found on the inside cover of the heat exchanger electrical box. Both diagram types are also

placed inside the shipping/warranty packet secured in the evaporator section.

Содержание gForce Ultra

































































Результаты поиска

Содержание gForce Ultra

Отзывы:

Похожие инструкции для gForce Ultra

Бренды по названию

Популярные бренды

Data Aire gForce Ultra, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание gForce Ultra

Отзывы:

Похожие инструкции для gForce Ultra

Бренды по названию

Популярные бренды