Data Aire gForce Ultra Скачать руководство пользователя страница 11

Страница: 11 / 64

The unit may be too tall to fit through a doorway while on the skid. Measure the unit and doorway

heights and refer to the installation plans to verify clearances prior to moving the unit.

WARNING:

Use care when moving. Improper handling could result in injury.

Proper care should be taken when uncrating the unit. The packaging has wrap

ping bands with sharp edges that are under tension, crating has staples and

splinters. Proper protective equipment should be worn by qualified personnel.

2.4 Rigging
Move the unit in its upright position to the installation site. It is recommended that the unit be protected

from damage to the decorative doors during any storage or moving. Removal of the decorative doors

is easily accomplished and may be done without moving the equipment.

The shipping skid should be left in place if the unit is being moved with a forklift. If the unit is being

lifted, use spreader bars to prevent damage to the doors and panels.

The unit has 3/4” (19mm) holes in the shipping skid to which casters with 3/4” (19mm) stems can be

attached. This allows easy movement down halls, into elevators and through doorways. If clearance

is a problem the casters may be inserted directly into the bottom of the 1” (25mm) tubular steel corner

posts at the bottom of the unit.

WARNING:

Improper lifting or moving of the equipment may result in damage

to the decorative doors, panels or frame members.

2.5 Locating the Unit

Verify that the floor is level, solid and sufficient to support the unit. When installing the unit, sufficient

space must be allowed for airflow clearance, wiring, plumbing and service access

. It is recommended

that each side and front have a clearance of at least 36” (914mm) to allow the doors to swing open

and for servicing the unit.
The doors on some sides may not require as much service clearance. Refer to the particular unit

component breakdown drawings for assistance. Rear clearance is not required, but 1” to 2” (25 to

50mm) of clearance is suggested.

For the best air distribution, the unit should be centered against the longest wall, distributing the cold

air as close to heat load as possible, unless the unit is ducted. The unit should not be placed near any

corner of the room or at the end of a long, narrow room. Install the units as close as possible to the

largest heat load. Multiple units should be evenly spaced, as far apart as possible. It is recommended

to install an under-floor water detection system.

NOTE:

Condensation formation and frequent humidifier flushing are normal

functions of this equipment. Proper drain connections must be made to ensure

proper removal. Unit will require water connections for condensate removal

and possibly for humidifier makeup water, chilled water and/or hot water. In

stallation of units above equipment that could sustain water damage should be

avoided.

Содержание gForce Ultra

































































Результаты поиска

Содержание gForce Ultra

Отзывы:

Похожие инструкции для gForce Ultra

Бренды по названию

Популярные бренды

Data Aire gForce Ultra, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание gForce Ultra

Отзывы:

Похожие инструкции для gForce Ultra

Бренды по названию

Популярные бренды