background image

Data Aire’s dap4 Modbus TCP/IP 

 

Document:

 

600

000

961

 

version

 

4.0

 

7

 

 

Point

 

Index

 

Description

 

Read/

Write

 

Variable

 

Name

 

Data

 

Type

 

Modbus

 

TCP/IP

 

32 

Temperature deadband for heating in economizer mode* 

R/W 

Econ_Ht_Deadband 

40033 

33 

Amount temp must change for each stage of heat/cool* 

R/W 

Stage_sp 

40034 

34 

Dewpoint setpoint for economizer* 

R/W 

Dewpoint_Hi_SP 

40035 

35 

deadband of dewpoint for economizer* 

Dewpoint_Hi_Dband 

30036 

36 

Lower limit of dewpoint for economizer* 

R/W 

Dewpoint_Lo_SP 

40037 

37 

deadband of low dewpoint for economizer* 

Dewpoint_Lo_Dband 

30038 

38 

deadband of enthalpy for economizer* 

Enthalpy_Deadband 

30039 

39 

Offset for Outside Air Temperature probe* 

R/W 

Ain_offs 

40040 

40 

Temperature of the outside air* 

Outside_Temp 

30041 

41 

Dew point of outside air* 

Outside_Dewpt 

30042 

42 

Dew point of return air* 

Ret_Air_Dewpt 

30043 

43 

Setpoint for fan modulation by return or rack temperature* 

R/W 

RA_Fan_Setpoint 

40044 

44 

Amount from setpoint before fan starts ramping up* 

R/W 

RA_Fan_Deadband 

40045 

45 

The highest of the rack temp sensors connected to this unit* 

Rack_Temp 

30046 

46 

The highest rack temp of all units in this zone* 

Zone_Rack_Temp 

30047 

47 

Value of rack temperature sensor #1* 

Rack_T1 

30048 

48 

Value of rack temperature sensor #2* 

Rack_T2 

30049 

49 

Value of rack temperature sensor #3* 

Rack_T3 

30050 

50 

Temperature setpoint of the Zone Master* 

Master_Temp_Setpoint 

30051 

Lower limit alarm of discharge air temp* 

R/W 

Disch_Air_Lo_SP 

45002 

Relative humidity displayed as xx% 

Humidity_dis 

35003 

Cooling Stages On = Cooling stages are currently on – This point applies to 
DX unit only 

Stages_On 

35004 

Number of heat stages running 

Heaters_On 

35005 

Maximum humidity in last 24hrs 

Maximum 

35006 

Minimum humidity in last 24hrs 

Minumum 

35007 

Cooling Utilization Over Last Hour -Percentage of cooling is used in the last 
hour of operation; this point applies to DX unit. 

Comp_duty 

35008 

Heating Utilization Over Last Hour -Percentage of heating is used in the 
last hour of operation 

Heat_duty 

35009 

Humidifier Utilization Over Last Hour -Percentage of humidifier is used in 
the last hour of operation 

Hum_duty 

35010 

10 

Compressor 1 Runtime -This point applies to DX unit with one compressor 
-high 

R C1_Hours_H 

35011 

11 

Compressor 1 Runtime -This point applies to DX unit with one compressor 
-low 

R C1_Hours_L 

35012 

12 

Compressor 2 Runtime -This point applies to DX unit with dual compressor 
- high 

R C2_Hours_H 

35013 

13 

Compressor 2 Runtime -This point applies to DX unit with dual compressor 
- low 

R C2_Hours_L 

35014 

14 

Heater 1 Runtime - high 

Ht1_Hours_H 

35015 

15 

Heater 1 Runtime - low 

Ht1_Hours_L 

35016 

16 Current 

second 

R  CURRENT_SECOND 

35017 

Содержание dap4 touch














Отзывы: