Dantel 49013 Скачать руководство пользователя страница 2

Страница: 2 / 10

AGE

49013-1297 <90-00034>

ORDERING INFORMATION

NOTE: This section lists the different options available for this product. To order any of the avail-

able options, contact Dantel Inside Sales through our toll-free number, 1-800-432-6835.

OPTION NUMBER

FEATURES

B12-49013-00

202 Tone Modem Subassembly

GENERAL DESCRIPTION

he Dantel 49013 202 Tone Modem Subassembly is used in

support of Dantel’s 460 Alarm and Control System. It con-

verts digital data into frequency shifted tones and enters it into
a data transmission system.

It also receives frequency shifted tones from a transmission
system and converts them into digital data. It operates as a Bell
202 full-duplex modem at a data rate of 1200 baud.

CIRCUIT DESCRIPTION

he 49013 202 Tone Modem Subassembly functional sche-

matic is shown in Fig. 1. The subassembly consists of:

♦

Transmit (TX) transformer

♦

Receive (RX) transformer

♦

Signal level pads

♦

Input/output buffers

♦

An FSK modem IC

♦

A Microcontroller 87C51

♦

A frequency control crystal

♦

Front panel test switch

♦

An LED driver

♦

Input power protection

UPDATED

Содержание 49013











Результаты поиска

Содержание 49013

Отзывы:

Похожие инструкции для 49013

Бренды по названию

Популярные бренды

Dantel 49013, Руководство по установке и эксплуатации

Результаты поиска

Содержание 49013

Отзывы:

Похожие инструкции для 49013

Бренды по названию

Популярные бренды