Dantel 46034 Скачать руководство пользователя страница 7

46034-0997 <90-00030>

 P

AGE

 7

APPLICATION INFORMATION

S

UMMING

 

AND

 D

ISTRIBUTION

 A

PPLICATIONS

Fig. 3 shows a switch setting diagram for summing applications.

Each data port to be summed has its bus output switched to the

bus. The data port that is to receive the summed data from the

contributing data ports has only its bus input switched to the

bus. The switches also can be set for distribution of communica-

tions using a common data bus. The input from one port distrib-

utes to the output of the other ports.
The module’s data communication buses route to the edge

connector which allows for bus expansion (pins 45 through 50).

Additional 46034 Hubbing Modules can share any or all of the

same buses which provides data summing/distribution/bridging

between data ports in different modules.

B

RIDGING

 A

PPLICATIONS

Fig. 4 shows a switch setting diagram for bridging applications

using half-duplex communication. Each data port on the data

bridge must have bus input and output switches set to the bus

being used. Because each data port’s bus input and output feed

to a common OR gate, the data port putting data on the bus

cancels its own input at the OR gate.
Fig. 5 shows a switch setting diagram for an RS-232 bridging

application using full-duplex communication. Module strapping

lets each data port provide either an RS-232 or RS-422 data

interface to the six data buses.
When strapped for RS-422 data, each of the eight data ports

receives and transmits data. When strapped for an RS-232

interface, two data ports may be required for each interface,

which limits the functioning data ports to four (not including

port nine). If CF and CA leads are not used, all eight ports are

available.

Содержание 46034



















Отзывы: