background image

 

Copyright 2005                                                                                    

27

                                

Vulcan V SERIES

 

 Owner’s Manual 

Canadian Comfort Industries                                      

www.stovesunlimited.com

                                                     Dansons Group Inc. 

Window

Burn Pot

Burn Grate

Heat Tubes

Tube Scraper

Ash Pit

R

EQUIRED 

R

OUTINE 

C

LEANING

 

 

Proper care of your 

VULCAN “V” Series 

pellet shop and home heater is required for peak, sustained performance.  

The need for and frequency of cleaning depends on the amount of pellets burned, pellet quality, length of time 
since last cleaning and the quality of the fire.  While becoming acquainted with your new stove and the types of 
local pellets, i

nspect your BURN GRATE, BURN POT, HEAT TUBES, ASH PIT, and WINDOW daily and clean 

until a pattern of cleaning requirement is determined

.  As heating demands increase the need for stove and 

exhaust system cleaning and ash removal will increase.  

 

 

WARNING:  Disconnect the electrical cord prior to opening the sides of your stove or opening the exhaust 
system for any inspection, cleaning, maintenance or service work.  NEVER perform any inspection, 
cleaning, maintenance or service on a HOT STOVE or when the electrical cord is plugged in. 

 

 

EVERY 2 –3 DAYS / WEEKLY 

 

BURN GRATE

:  [COLD STOVE ONLY]

 Clean as 

needed, scraping off any residue that may stick to grate 
bottom or sides.  Ensure that the holes are clean and 
unrestricted.  CAUTION:  When replacing the grate make 
sure it fits properly in the burn pot with the lip on the burn 
grate, toward the front of your stove. 

 

BURN POT:

  [COLD STOVE ONLY]

  Remove the 

burn grate.  Clean out the burn pot as needed. Do not 
push the fly ash to the back of the pot, as this will restrict 
the air flow and performance of the appliance.  

 

HEAT TUBES:

 [COLD STOVE ONLY} 

With your 

stove's main door closed  pull the HEAT TUBE 
SCRAPER ROD forward and backwards a few times.  As 
different types of pellets produce different amounts of 
ash, cleaning the tubes enables the heat exchange to 
operate efficiently.  

CAUTION

:  On a burning stove the heat tube scraper rod 

will be hot.   

 

ASH PIT:  

Monitor the ash level on a weekly basis. 

Ash content is a good indication of fuel efficiency and quality. Refer to “Safety Precaution”  for safe disposal 
of ashes. 
 

 

WINDOW CLEANING:

  [COLD STOVE ONLY as hot glass may cause serious burns]

 To enjoy a 

clear view of the fire you should clean your window as needed with a soft cloth or paper towel. You may use 
a glass cleaner to remove heavy build up on the window. 

HOME TIP:

 Dampen a piece of newsprint with 

water, dip this into the fly ash, then rub down the glass.  This works like a charm. Do not use abrasive 
chemical cleaners 
 

DO NOT OPERATE STOVE WITH BROKEN GLASS AS LEAKAGE OF FLUE GASES MAY RESULT. 

 
 
 
 
 
 

Содержание CC2






































Отзывы: