Danfoss VLT CDS 803 страница 59 Скачать руководство пользователя

Страница: 59 / 92

14-63 Min Switch Frequency

Set the minimum switching frequency allowed by the output
filter.

Option:

Function:

[2]

2.0 kHz

[3]

3.0 kHz

[4]

4.0 kHz

[5]

5.0 kHz

[6]

6.0 kHz

[7]

8.0 kHz

[8]

10.0 kHz

[9]

12.0 kHz

[10]

16.0 kHz

14-90 Fault Level

To customize fault levels, use this parameter.
Use

[0] Off

with caution as it ignores all warnings and alarms for

the selected source.

Option:

Function:

[3]

Trip lock

[4]

Trip w.
delayed reset

[5]

Flystart

3.11 Main Menu - Drive Information - Group

Parameter group containing frequency converter
information such as operating data, hardware configu-
ration, and software versions.

3.11.1 15-0* Operating Data

15-00 Operating hours

Range:

Function:

0 h

[0 - 0x7fffffff.
h]

View how many hours the
frequency converter has run. The
value is saved when the frequency
converter is turned off.

15-01 Running Hours

Range:

Function:

0 h

[0 - 0x7fffffff.
h]

View how many hours the
compressor has run. Reset the
counter in

parameter 15-07 Reset

Running Hours Counter

. The value is

saved when the frequency
converter is turned off.

15-03 Power Up's

Range:

Function:

[0 -
2147483647 ]

View the number of times the
frequency converter has been
powered up.

15-04 Over Temp's

Range:

Function:

[0 - 65535 ]

View the number of frequency
converter temperature faults that
have occurred.

15-05 Over Volt's

Range:

Function:

[0 - 65535 ]

View the number of frequency
converter overvoltages that have
occurred..

15-06 Reset kWh Counter

Option:

Function:

[0]

Do not reset

[1]

Reset counter

To reset the kWh counter to 0,
select

[1] Reset

and press

[OK]

15-07 Reset Running Hours Counter

Option:

Function:

[0]

Do not reset

[1]

Reset counter

To reset the running hours counter,
select

[1] Reset counter

and press

[OK]

(see also

parameter 15-01 Running Hours

15-08 Number of Starts

Range:

Function:

[0 -
2147483647 ]

States the number of starts
executed on the frequency
converter. The counter can be reset
in

parameter 15-07 Reset Running

Hours Counter

. The value is saved

when the frequency converter is
turned off.

15-09 Number of Auto Resets

Range:

Function:

[0 -
2147483647 ]

States the number of auto resets
executed by the frequency
converter.

3.11.2 15-3* Alarm Log

Parameters in this group are array parameters, where up to
10 fault logs can be viewed. [0] is the most recent logged
data, and [9] the oldest. Fault codes, values, and time
stamp can be viewed for all logged data.

15-30 Alarm Log: Error Code

Range:

Function:

[0 - 255 ]

View the fault code and lookup its
meaning in

chapter 4 Trouble-

shooting

Parameters

Programming Guide

MG18P202

Содержание VLT CDS 803




























































































Результаты поиска

Содержание VLT CDS 803

Отзывы:

Похожие инструкции для VLT CDS 803

Бренды по названию

Популярные бренды

Danfoss VLT CDS 803, Руководство по программированию

Результаты поиска

Содержание VLT CDS 803

Отзывы:

Похожие инструкции для VLT CDS 803

Бренды по названию

Популярные бренды