Danfoss OSPE Скачать руководство пользователя | Manualshive

Страница: 40 / 48

background image

Assembling OSPE (continued)

OSPE with priority valve:
Place the O-ring (312) on plug (207 with 17 mm key
profile).

Screw in the plug (207) using a 17 mm

socket

spanner

45 ±5 Nm.

OSPE without priority valve:

Place the O-rings (312, 313) on plug (207 with 8 mm
Hex key profile).

Screw in the plug (207) using a 8 mm

Hex key.

45 ±5 Nm.

Insert the EH L&R cut off spool (242) with the spring bore
pointing outwards.

Insert the spring (241). Dimension of this spring: Wire
diameter: 2.2 mm Length: 50.2 ±0.8 mm

Place the O-ring (312) on plug (243). Screw in the plug

(243) using a 17 mm

socket spanner

45 ±5 Nm.

Service Manual

OSPE Steering Valve

Assembly

40

L1506577 • Rev 0001 • August 2015

«
...
38
39
40
41
42
...
»

Содержание OSPE

















































Отзывы:

Нет отзывов

Похожие инструкции для OSPE

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 52

Бренд: Samson Страницы: 20

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 426

Бренд: YASKAWA Страницы: 26

Бренд: YASKAWA Страницы: 210

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 400

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 466

Бренд: Ziton Страницы: 28

Бренд: Unico Страницы: 164

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды