Danfoss DGS-SC Скачать руководство пользователя страница 20

Страница: 20 / 26

Installation and Operation Guide | DGS Modbus

20 | RS8HJ102 |

Service

Read out of refrigerant (Gas) for the DGS is used for
Value according to "Danfoss standard list".

Refrigerant

Gas Full scale in ppm

32000

ppm

Fullscale ppm

Hours since last calibration

32000

hours

Burning hours

Status of the sensor warm up period
0 =Ready
1 = Warming Up

Startup flag

When cleared, clears calibration due alarm and resets the
burning hours parameter
0 = Calibration valid
1 = Calibration due

Reset cal

Failsafe operation of the Relay
0 = Not failsafe
1 = Failsafe

Relay failsafe

Enables Manual control of Relays.
Automatically falls back to Off after 10 min.

Maunal Control

Status of the high alarm relay
0 = No alarm signal
1 = alarm signal

Alarm Relay

Status of the buzzer
0 = inactive
1 = active

Sounder

Status of the red LED
0 = off
1 = on

Red LED

Status of the green LED
0 = off
1 = on

Green LED

Alarms

Limit alarm
0 = Alarm not active
1 = Alarm, gas limit exceeded

Limit alarm

Sensor saturated
0 = OK
1 = Fault. Out of range under test

Sensor saturated

Sensor out
0 = OK, sensor in place
1 = Fault, Sensor out or removed

Sensor out

Calibrate sensor
0 = OP, Sensor not due for calibration
1 = Warning, Due for calibration

Calibrate sensor

Warning limit alarm
0 = OK, Gas level below warning level
1 = Warning, Gas level above warning level and delay expired

Warning limit al.

Содержание DGS-SC



























Результаты поиска

Содержание DGS-SC

Отзывы:

Похожие инструкции для DGS-SC

Бренды по названию

Популярные бренды

Danfoss DGS-SC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DGS-SC

Отзывы:

Похожие инструкции для DGS-SC

Бренды по названию

Популярные бренды