Danfoss DGS-SC Скачать руководство пользователя страница 17

Страница: 17 / 26

Installation and Operation Guide | DGS Modbus

RS8HJ102 | 17

To install the DGS unit on the network, first set the network ad-
dress (see section 4.4 of this manual). Following this, the DGS unit
can be installed on the network and configured in the Front End.
(see Front End manual for specific details)
For communication speeds other than the default 38.4k, please
refer to section 4.4 of this manual and the manual of the system
manager.

7. Installation

Survey of functions

Function

Parameter by operation via data

communication

Gas level

Actual gas level in %

The actual gas level is displayed here as a percentage of the full scale ppm. The full scale ppm

can be viewed in the “Service” group.

Example: If the full scale value is 1000ppm and the sensor is measuring 400ppm, the value is

40%

Gas level %

(shown in all menu displays)

Actual gas level in ppm

The actual gas level is displayed here as a ppm value.

Gas level ppm

(shown in all menu displays)

Alarms

Alarm settings

As default the potentiometer in the DGS unit defines the alarm limit (see section 4.3) and the

warning function is disabled.

By changing the value of the “Alarm Limit” parameter, the alarm parameter defines the alarm

limit and the Warning function can be enabled.

Changing the alarm limit parameter to zero will enable the potentiometer alarm setting and

disable the warning function. The potentiometer value is read back to the Alarm Limit param-

eter and presented (zero is overwritten).

It is not possible to adjust the alarm limit below the actual warning limit.

It is not possible to adjust the warning limit above the actual alarm limit.

If this is attempted, the value is considered invalid and ignored.

Critical alarm indication

Common indication of alarms (any alarms active excl. warnings)

The indication is given as soon as the alarm condition is present regardless of any alarm time

delays

0 = No active alarm(s)

1 = Alarm(s) active

GD alarm

General alarm incication

Common indication of any alarms incl. warnings

The indication is given as soon as the alarm condition is present regardless of any alarm time

delays

0 = No active alarm(s) or warning(s)

1 = Alarm(s) or warning(s) active

Common errors

Alarm limit in %

The alarm limit can be set as a percentage of full scale ppm. The full scale ppm can be viewed

in the “Service” group.

Example: If the full scale value is 1000ppm and the sensor should give alarm at 500ppm, the

value is entered as 50%

Alarm limit %

Alarm limit in ppm

The alarm limit is entered here as a ppm value.

Alarm limit ppm

Time delay for level alarms

High alarm delay in minutes.

If set to 0, the hardware jumper configuration is used. This means that the hardware configured

delay will be shown (zero is overwritten).

If set to a value above zero, this value is used instead of the hardware jumper configuration.

The value is used both as delay for limit alarm and warning.

Alarm delay

Reset alarm in DGS unit

Will mute the buzzer and reset the alarm relay. The alarm remains active (LED and Modbus)

until the alarm condition disappears.

Reset alarm

SW 1.1x

Содержание DGS-SC



























Результаты поиска

Содержание DGS-SC

Отзывы:

Похожие инструкции для DGS-SC

Бренды по названию

Популярные бренды

Danfoss DGS-SC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DGS-SC

Отзывы:

Похожие инструкции для DGS-SC

Бренды по названию

Популярные бренды