Danfoss AK-LM 330 Скачать руководство пользователя

Страница: 73 / 80

AK-LM

330

RS8FR302 © Danfoss 2015-08

Read codes

Normally the selected temperature signal can be read from the

display, but under certain conditions the display may show other

codes in order to notify the user of various operating states.

Function

Display readout

OFF

When the "main switch" is set to OFF, the display will read "OFF"

PAS

Requirement for access code. If operation of the display is to be

protected by an access code, both the definition and the access

code must be set in the controllers' authorisation menu for the

local display (LOCD).

Alarm

The three LED's will flash if an alarm is triggered. The alarm code

can be viewed by pressing the top button. Pressing the button will

also reset the alarm relay

- - -

When three dashes appear, the valid temperature reading is faulty

(sensor switched off or short-circuited), or else the display has been

deactivated.

Menu overview:

Parameter

name

Function

At start-

r12

Main switch:

0: Controller stopped

1: Regulation

o93

Configuration lock

You can only select a preset configuration or change refriger-

ant when the configuration lock is open.

0 = Configuration open

1 = Configuration locked

o62

Selection of predefined configuration.

This setting will give a choice from a series of predefined

combinations, which at the same time establish the connec-

tion points.

At the end of the manual there is an overview of the options

and connection points.

After configuration of this function, the controller will shut

down and restart.

u1-u31

u10

Readouts for use in service situations

Temperature measurement, thermostat 1

Temperature measurement, thermostat 2

Temperature measurement, thermostat 3

Temperature measurement, thermostat 4

Temperature measurement, thermostat 5

Temperature measurement, thermostat 6

Temperature measurement, thermostat 7

Temperature measurement, thermostat 8

Temperature measurement, thermostat 9

Temperature measurement, thermostat 10

u11

u12

u13

u14

u15

Pressure measurement, pressostat 1

Pressure measurement, pressostat 2

Pressure measurement, pressostat 3

Pressure measurement, pressostat 4

Pressure measurement, pressostat 5

u16

u17

u18

u19

u20

u21

u22

u23

u24

u25

u26

u27

u28

u29

u30

u31

Status on alarm DI 1

Status on alarm DI 2

Status on alarm DI 3

Status on alarm DI 4

Status on alarm DI 5

Status on alarm DI 6

Status on alarm DI 7

Status on alarm DI 8

Status on alarm DI 9

Status on alarm DI 10

Status on alarm DI 11

Status on alarm DI 12

Status on alarm DI 13

Status on alarm DI 14

Status on alarm DI 15

Status on alarm DI 16

X = When the controller is not set up, the display will only

read the marked settings

A01

A02

A03

A04

A05

A06

A07

A08

A09

A10

A11

A12

A13

A14

A15

A16

A17

A18

A19

A20

High alarm thermostat 1

Low alarm thermostat 1

High alarm thermostat 2

Low alarm thermostat 2

High alarm thermostat 3

Low alarm thermostat 3

High alarm thermostat 4

Low alarm thermostat 4

High alarm thermostat 5

Low alarm thermostat 5

High alarm thermostat 6

Low alarm thermostat 6

High alarm thermostat 7

Low alarm thermostat 7

High alarm thermostat 8

Low alarm thermostat 8

High alarm thermostat 9

Low alarm thermostat 9

High alarm thermostat 10

Low alarm thermostat 10

A21

A22

A23

A24

A25

A26

A27

A28

A29

A30

Low alarm pressostat 1

High alarm pressostat 1

Low alarm pressostat 2

High alarm pressostat 2

Low alarm pressostat 3

High alarm pressostat 3

Low alarm pressostat 4

High alarm pressostat 4

Low alarm pressostat 5

High alarm pressostat 5

A31

A32

A33

A34

A35

A36

A37

A38

A39

A40

Low alarm voltage input 1

High alarm voltage input 1

Low alarm voltage input 2

High alarm voltage input 2

Low alarm voltage input 3

High alarm voltage input 3

Low alarm voltage input 4

High alarm voltage input 4

Low alarm voltage input 5

High alarm voltage input 5

A41

A42

A43

A44

A45

A46

A47

A48

A49

A50

A51

A52

A53

A54

A55

A56

Alarm DI 1

Alarm DI 2

Alarm DI 3

Alarm DI 4

Alarm DI 5

Alarm DI 6

Alarm DI 7

Alarm DI 8

Alarm DI 9

Alarm DI 10

Alarm DI 11

Alarm DI 12

Alarm DI 13

Alarm DI 14

Alarm DI 15

Alarm DI 16

A60

Manual control of DO / DI

E01

E02

Sensor alarm

System alarm

- - 1

Initiation. Display is connected to output A. (- - 2 = output B, etc.)

Alarm overview:

Содержание AK-LM 330

















































































Результаты поиска

Содержание AK-LM 330

Отзывы:

Похожие инструкции для AK-LM 330

Бренды по названию

Популярные бренды

Danfoss AK-LM 330, Руководство по конструкции

Результаты поиска

Содержание AK-LM 330

Отзывы:

Похожие инструкции для AK-LM 330

Бренды по названию

Популярные бренды