D&H DH05C Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 106

background image

76

Fahrzeug-/Funktionsdecoder

ab Firmware-Version 1.11

76

Locomotive/Vehicle function decoder

from firmware version 3.12

• Revert the driving direction with the driving controller (turn the driving controller to the left beyond the keystroke

until your hear a click), hold the controller and and push GO button.

• After about one second the lights of the engine are flashing, the decoder is now in programming mode.

Short mode

•  After changing in programming mode the decoder is in short mode.
  The engine lighting flashes slowly and periodically.
•  Enter now the number of the CV you want to change, e.g. 01 (double digit).
•  Activate the reversion of the driving direction for confirmation. Lighting is now flashing shortly two times.
•  Enter now the new value for the CV, e.g. 15 (double digit).
•  Activate the reversion of the driving direction for confirmation.
  The lighting flashes.
•  You may now enter further CV values which you want to change.

The programming mode is left by selection of CV80 or by turning off and on the track power (push STOP button and then
again GO button).

Long mode

•  You get the longe mode by entering in short mode value 07 in CV07 at first.
  The decoder confirms changing in long mode by slow fashing of the lighting.
•  Enter now then hundredth and ten‘s digit of the CV, which you want to change.
  Example: CV124 should be changed: Enter ‘12‘.
•  Activate the reversion of the driving direction for confirmation. The lighting flashes long and short (periodically).
•  Enter now the unit place of the CV in double digit. See example: ‘04‘.
•  Activate the reversion of the driving direction for confirmation. The lighting flashes long - short - short (periodically).
  The decoder waits now for entering the CV value.

«
...
74
75
76
77
78
...
»

Содержание DH05C











































































































Отзывы:

Нет отзывов

Похожие инструкции для DH05C

Бренд: Lenze Страницы: 132

Infinity IEC-2001

Бренд: LevelOne Страницы: 2

Бренд: Engel Страницы: 42

Rapid Shutdown Box-Duo

Бренд: Fronius Страницы: 60

Бренд: Saftronics Страницы: 113

Бренд: La Marche Страницы: 32

Бренд: B&R Страницы: 45

Бренд: Paradox Страницы: 2

VARIOMAT 2 11MM

Бренд: Calpeda Страницы: 64

Бренд: Siqura Страницы: 2

Бренд: Odorox Страницы: 11

Бренд: Xnexus Страницы: 20

Бренд: B PLUS TV Страницы: 10

Бренд: LC Страницы: 44

SA-1000K Series

Бренд: Samlexpower Страницы: 23

Бренд: COMPANION Страницы: 16

Бренд: Hall Research Technologies Страницы: 8

Бренд: Wagan Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды