D&H DH05C Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 106

background image

38

Fahrzeug-/Funktionsdecoder

ab Firmware-Version 1.11

38

Locomotive/Vehicle function decoder

from firmware version 3.12

The PD06A vehicle decoder for miniature motors is our particularly small vehicle decoder for SX1, SX2 and DCC
operation.

•  No support for MM mode
•  No support of SX1 programming (but SX1 operation is possible through SX2 parameter programming)
•  No SUSI interface
•  No extended function assignments (i.e.: no conditions, no initial mapping etc.)
•  No automatic coupling process
•  No braking with asymmetrical digital voltage and no slow driving
•  No brake ramp

The PD12A, PD18A and PD21A vehicle decoders are particularly inexpensive vehicle decoders for pure DCC
operation and DC analog.

•  No support of the operating modes SX1, SX2 and MM
•  No SUSI interface and no unamplified function outputs
•  No extended function assignments (i.e.: no conditions, no initial mapping etc.)
•  No automatic coupling process (but timers for switching off AUX1 and AUX2 are available)

5.2 Installation of the decoder

Before installation check if the locomotive is in perfect electrical and mechanical condition. Defects and dirt must be
eliminated first. Pay attention to the instructions of the locomotive producer.
Only locomotives running smoothly in analogue mode should be equipped with digital decoder. New locomotives should
be run in at least 30 minutes in each driving direction.

«
...
36
37
38
39
40
...
»

Содержание DH05C











































































































Отзывы:

Нет отзывов

Похожие инструкции для DH05C

Бренд: Datavideo Страницы: 35

Бренд: A2Z Ozone Systems Страницы: 13

Бренд: A2Z Ozone Страницы: 17

Бренд: Yamaha Страницы: 30

BLUESTREAM DA44AU

Бренд: Dante Страницы: 12

Бренд: Lumantek Страницы: 14

Бренд: Premier Страницы: 12

Бренд: ATEN Страницы: 2

Бренд: IONODES Страницы: 23

Бренд: Digi Страницы: 6

Бренд: Cross Technologies Страницы: 24

Бренд: Delta Electronics Страницы: 181

Бренд: Hopewind Страницы: 50

Бренд: B.M.C. Страницы: 8

Бренд: M-system Страницы: 3

Indigo Wallbox Q-Down

Бренд: Crystal Vision Страницы: 68

Бренд: TV One Страницы: 12

Бренд: Hall Research Technologies Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды