散件 KIT
配件图仅做参考用，您收到的实
物可能因为修改/优化的原因导
致与图片有略有不同。
Photos shown here just for
reference, the product you
received maybe slightly differ
from the photos due to
continuous improvement on
products.
1
01
机翼组装
Assemble the Wing
A
B1
B2
B3
C1
C2
C3
C4
C5
D1
E1
E2
F
G
H
I
J1
J2
K
L
M
D3
D2
A:机身
B1:机翼
B2:副翼
B3:襟翼
C1:水平尾翼
C2:升降舵
C3:方向舵
C5:升降舵连接钢丝
D1:起落架
D2:机轮
D3:尾轮组
E1/E2:机翼连接碳杆
F:连杆
G:机轮罩
H:油动舵机架
I:魔术胶带
J1-J2:机翼固定件
K:纸合页
L:舵角
M:快装接头
01-1
01-2
在副翼，和襟翼的预留槽里插入纸合页，用少量CA胶水粘固。
Plug paper hinge into the pre-cutted slot of aileron and flap
wing.Stick it with a little CA glue.
把粘好纸合页的副翼襟翼插入机翼的预留槽，调整合适间隙。
Plug the aileron and flap wing into the pre-cutted slot of wings,
adjust appropriate space.
B3
K
B3
B2
B1
01-3
在连接处点入少量CA胶粘合固定。
Fasten with a little CA glue on the joint.
用镊子挑出预埋的引导线。
Pick out the pre-embedded guiding wire with tweezers.
在机翼的背面用美工刀切开舵机的空位，和舵机线导出孔。
Cut the servo hole and servo wire's guiding hole with
knife on the back of wings.
01-4
提示：此处需要切开的孔，可以用手摸来确定孔位，也可对着灯光同过光线
来确定孔位。
Note:Touch the holes to confirm the correct hole position, or confirm
it at the bright light.
01-5
01-6
在安装机翼上舵机前，您的舵机可能需要接延长线。
Before installing servo of the wings, your servo may need to connect
extension line.
把最远端的引导线绑在舵机线上，然后拉另一端的引导线，让舵机线穿入机
翼内。
Bind the farthest guiding line on the servo line, then pull the other
end of the guiding line,let the servo line to penetrate into wings.
拉到中段时再绑上另一个
舵机的舵机线，继续拉动
引导线。
Bind another servo line
when you pull it in the
middle section,
continue to pull the
guiding line.
01-7
01-8
C4:垂直尾翼
M:Quick Joint
L:Control Horn
K:Paper Hinge
J1-J2:Wing Fixed Parts
I:Magic Tape
H:Servo Frame for Gas Power
G:Wheels Cover
F:Linkage Rod
E1/E2:Carbon Rod for Connecting Wings
D3:Tail Wheel Combo
D2:Wheels
D1:Landing Gear
C5:Steel Wire for Connecting Elevator
C4:Vertical Tail
C3:Rudder
C2:Elevator
C1:Horizontal Tail
B3:Flap Wing
B2:Aileron
B1:Wing
A:Fuselage
