background image

Danaher Motion Kollmorgen Speciality Electronics 

Personality Module for CD-LITE 

SERVO

STAR

 CD-LITE User Manual 

27 

Personality Module for CD-LITE 

The Personality Module is used to easily configure multiple CD-Lite servo drives. After one servo drive 
has been configured and tuned, the parameters of that drive are uploaded into the module. In order to 
configure additonal servo drives with the same parameters, the module is plugged into those drives and 
the parameters downloaded into the drives. 

The same parameters that are stored in an SSV file, are stored in the Personality Module. In addition, 
when downloading the parameters, CONFIG and SAVE commands are included. 

Preparation 

The CD-LITE should have firmware version 0.1.3 or higher. 

Description and Operation 

The Personality Module has a female D-9 connector to plug into the serial connector (C1) on the front 
panel of the CD-Lite. The Personality Module has two switches and one green LED on it: 

A recessed switch is used for UPLOADING parameters from the drive into the Personality Module. The 
tip of a pen or some similar instrument is needed to access the switch. The switch needs to be pressed for 
a minimum of 2 seconds in order to activate the upload procedure. During the upload, the display will 
show 3 bars flashing, first the lower, then the middle, and then the upper. 

An easy access switch is used for DOWNLOADING parameters from the Personality Module to the 
drive. Pushing this button downloads the values from the Personality Module to the drive. During the 
download, the CD-Lite display shows 3 bars flashing, first the upper, then the middle, and then the lower. 
This action takes a few seconds. 

The Green LED is lit to indicate that the system is powered on. 

Error Display 

♦ 

If an error occurs during DOWNLOAD from the Personality Module, the display on the 7-segment 
flashes “–7”. 

♦ 

If an error occurs during UPLOAD to the Personality Module, the display on the 7-segment flashes 
–6. 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание SERVOSTAR CD-LITE


















































Отзывы: