DANA TRAC-LOK 60 Скачать руководство пользователя страница 10

Страница: 10 / 15

MODEL 60 TRAC-LOK

FIGURE #21

1015--2"1

Reposition case on bench as shown. Assemble the

adapter plate into the side gear. Apply a small amount

of grease into the centering hole of the adapter plate.

FIGURE #22

101&-22

Assemble the other clutch pack and side gear as

shown. Make sure the clutch pack stays assembled to

the side gear splines, and that the retainer clips are

completely seated into the pockets of the case.

FIGURE #23

1015·23

Hold the clutch pack in position and insert the

threaded adapter into top side gear, insert forcing

screw. Tighten forcing screw into bottom plate. This

will hold both clutch packs in position.

With tools assembled into the case, position case

onto the axle shaft by aligning the splines of the side

gear with those of the shaft.

FIGURE #24

101S.24

Loosen forcing screw slightly. Assemble both pinion

mate gears as shown. Hold gears in position by hand.

While holding gears in place, insert turning bar into

case. Pull on bar to rotate case allowing gears to turn.
Make absolutely sure that the holes of the pinion mate

gears are in alignment with holes of the case.

FIGURE #25

1015-25

Prelubricate spherical washers. Torque forcing

screw until it is tight. This will collapse the Belleville

plates and allow clearance bet ween gears. Assemble

spherical washers into case. Use a small screwdriver to

push washers into place.

Содержание TRAC-LOK 60
















Результаты поиска

Содержание TRAC-LOK 60

Отзывы:

Бренды по названию

Популярные бренды

DANA TRAC-LOK 60, Руководство по обслуживанию

Результаты поиска

Содержание TRAC-LOK 60

Отзывы:

Бренды по названию

Популярные бренды