background image

 

6

7

ADJUSTMENT OF AIR SPEED AND TEMPERATURE 

• Insert Philips screwdriver or flat notch through the hole at the bottom of the cover and  
  place the screw head on the potentiometer screw (see drawing below) 
• Adjust air speed and temperature on the VR potentiometer:  
  Clockwise to increase air speed and temperature (+) 
  Counterclockwise to decease air speed and temperature (-) 
• Be careful not to overturn the adjustment screw

ADJUSTMENT OF SENSOR RANGE 

 

The sensor range is adjsutable between 100 mm and 230 mm. Standard range 170 mm 

± 20 mm. 

 
• Switch off power and dismount the cover by loosening (2) screws at the bottom   
• Use a small Philips screwdriver or similar to adjust the sensor on the VR screw: 
  Clockwise to increase sensor activation range (+) 
  Counterclockwise to decrease sensor activation range (-) 
• The sensor activation range should be adjusted to its environments, e.g. light and  
  distance to the bottom of the sink 
• Be careful not to overturn the sensivity adjustment

RECOMMENDED INSTALLATION HEIGHT 

From bottom edge of hand dryer above finished floor.

Men

1270 mm (50”)

Women

1194 mm (47”)

Children 4-7 years

889 mm

(35”)

Children 8-10 years

991 mm

(39”)

Children 11-13 years

1092 mm (43”)

Children 14-16 years

1194 mm (47”)

Wheelchair users

1016 mm (40”)

PRODUCT APPLICATION

 

•  Shake excess water from hands 
•  Place hands under the dryer to turn it on 
•  Rub hands lightly and rapidly 
•  Stops automatically after hands are removed.

CLEANING AND MAINTENANCE

Routine cleaning and maintenance is recommended every 12 months. 
• Cut the power 
• Unscrew (2) bottom security screws 
• Remove the cover 
• Clean the cabinet inside and remove dust/dirt. You can use compressed air 
• Check carbon brushes in the motor. If carbon brushes are worn (

≤ 10 mm graphite  

 

 remaining),  they must be replaced 
• Clean sensor lense on both sides 
• Do not rinse with running water 
• Use a damp cloth and mild cleaning solution. Never use cleaning detergents with an  

 

  abrasive effect  
• Replace cabinet front and tighten screws. Be careful not to overtighten screws

Содержание 288







Отзывы: