Dalsa Piranha HS Series Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 123

background image

Piranha HS-xx RoHS User Manual

Teledyne DALSA

03-032-20013-03

43

4.4 Camera Output Format

4.4.1 How to Configure Camera Output

The Piranha H S cam eras offer great flexibility w hen configu ring you r cam era ou tp u t.
Using the

clm

com m and , you d eterm ine the cam era’s Cam era Link configu ration,

nu m ber of ou tp u t tap s, and bit d ep th. Using the

sot

com m and , you d eterm ine the

camera’s output rate. These two commands work together to determine your final camera
ou tp u t configu ration.

You can fu rther configu re you r read ou t u sing the

smm

command to select the camera’s

p ixel read ou t d irection.

The follow ing tables su m m arize the p ossible cam era configu rations for each of the H S-xx
cam era m od els. Refer to the figu re below for a d escrip tion on how to select you r cam e ra
ou tp u t.

Figure 25: How to Read the Camera Link Tables

Camera Link Mode Configuration (Controlled by

clm command)

Readout Direction(Controlled by

smm

command)

Pixel Rate
Configuration
(Controlled by

sot

command)

Command

Camera Link

Configuration

Camera Link Taps

Bit
Depth

smm 0 increment =1

smm 1 increment = -1

clm 2

Base

2 Camera Link taps
where:

1 = CCD taps 1 +2

2 = CCD taps 3+4

8

smm

0

=CL tap 1

(1-2048)

CL tap 2

(2049-4096)

smm 1

= CL tap 1

(4096-2049)

CL tap 2

(2048-1)

sot 160

= 80 MHz

strobe

(max line rate
36kHz)

sot 80

= 40 MHz

strobe

(Max line rate
18kHz)

Find the rows in the table
with a line rate greater than
or equal to your desired
line rate.

From the rows determined in part A,
find the

values in the table

with a throughput greater than or equal
to your your required throughput.

sot

From the rows determined by
part B, find the Camera Link modes
with your desired bit depth.

From the remaining rows determined
in part C, select an acceptable Camera Link
configuration. If none of the remaining
configurations are acceptable for your system,
you will have to reduce your bit depth
or line rate.

Set the pixel readout direction.
Note: Horizontal binning reduces
the number of pixels sent to the
frame grabber by the binning factor.

Note:

In the follow ing tables, a CCD tap refers to the actu al p hysical tap s on the sensor ,

w hile the Cam era Link tap s refer to the w ay the d ata is configu red for ou tp u t over
Cam era Link. For a d iagram illu strating sensor tap s, see section 1.3 Im age Sensor.

All manuals and user guides at all-guides.com

«
...
41
42
43
44
45
...
»

Содержание Piranha HS Series




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Piranha HS Series

Бренд: AgfaPhoto Страницы: 2

Бренд: Andor Technology Страницы: 2

Бренд: Targa Страницы: 386

Бренд: Xcellon Страницы: 16

TURBO HD 4K DS-2CE57U8T-VPIT

Бренд: HIKVISION Страницы: 12

Бренд: Axis Страницы: 98

Бренд: HANNspree Страницы: 24

EASYSHARE DX3700

Бренд: Kodak Страницы: 86

Бренд: Hyundai Страницы: 32

Бренд: Yashica Страницы: 24

Бренд: FujiFilm Страницы: 2

FASTCAM Mini AX100

Бренд: Photron Страницы: 63

Бренд: Olympus Страницы: 84

Бренд: Olympus Страницы: 156

CAMEDIA C-4040ZOOM

Бренд: Olympus Страницы: 196

Бренд: Casio Страницы: 82

Бренд: Quantum Instruments Страницы: 40

Бренд: Absen Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды