Dalsa Linea HS Series Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 128

background image

Linea HS Series Camera User's Manual

Camera Performance and Features

•

83

8.

Click on the Save LUT button to create a LUT file.

9.

This file can be loaded into the camera using the File Access features. It is saved with the
current Load / Save Configuration user set; ensure that a user set and not the factory set is
selected, otherwise the upload will fail.

10.

Deselect the Lookup Table | Enable feature.

11.

Return the Board parameters

Pixel Depth

= 8, and

Image Buffer

= 8-bits.

•

Important Points:

•

The frame grabber must be configured mono 12-bits in, 16 bits out.

•

In the Parameters explorer a frame grabber feature must be selected, not a
camera feature.

•

The Lookup table must be enabled to be created but should be disabled to
use the camera LUT.

Adjusting Responsivity and Contrast Enhancement

See the section Camera Control Category in Appendix A for GenICam features associated with this
section and how to use them.

Related Features:

It is best for camera performance to always use the maximum exposure time possible based on the
maximum line rate of the inspection system and any margin that may be required to accommodate
illumination degradation. However, it will be necessary to adjust the responsivity to achieve the
desired output from the camera. The camera has gain and black level (offset) features that can be

used to adjust the camera’s responsivity.

Gain and black level settings are applied as follows:

DN

out

= ((DN

in

+ Black Level) * Gain) * System Gain

X

X

+/-

black

level

(offset)

gain

system

gain

Figure 44: Black Level, Gain and System Gain Processing Chain

Refer to the Camera Processing Chain section for an overview of the entire processing chain.

For monochrome cameras gain adjustment is applied to all sensor array output rows; for the
multifield color model gain can be applied to each color array output row individually. Row gains
can be adjusted from 1 to ~4x. System Gain can be adjusted from 1 to 10x.

When an image contains no useful dark image data below a specific threshold, then it may be
beneficial to increase the contrast of the image.

«
...
81
82
83
84
85
...
»

Содержание Linea HS Series

































































































































Отзывы:

Нет отзывов

Похожие инструкции для Linea HS Series

EOS C300 Mark II

Бренд: Canon Страницы: 16

Бренд: MAGPiX Страницы: 30

Бренд: Navitel Страницы: 15

Бренд: Navitar Страницы: 1

ThermaCheck TC160

Бренд: Planck VISION SYSTEMS Страницы: 7

Бренд: Festo Страницы: 156

Бренд: IP Camera Страницы: 37

Efector 250 O3D301

Бренд: IFM Страницы: 9

CAMEDIA C-3020 Zoom

Бренд: Olympus Страницы: 180

Smart Lookever Camera

Бренд: Wulian Страницы: 20

MATRIX VISION GiGE VISION BVS CA-GX0-XAS2...

Бренд: Balluff Страницы: 94

Бренд: Konig Страницы: 48

Бренд: Mini Gadgets Страницы: 16

Бренд: G-Lenz Security Страницы: 14

Бренд: Olympus Страницы: 220

Бренд: Godox Страницы: 9

Бренд: Minolta Страницы: 96

180-View 180NT-P-CM

Бренд: Tamron Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды