DALBO MAXICUT Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 30

DALBO MAXICUT Скачать руководство пользователя страница 25

MAXICUT

Side 25

Removal/fitting wheel

Raise wheel frame before removing wheel. Wheels will then be raised free of
ground. Remove wheel nuts. Remove wheel. Replace wheel, hand-tighten wheel
nuts. Lower wheels to ground. Tighten wheel nuts to 300 Nm.

Ensure wheel nuts and wheel surfaces are clean to avoid nuts loosening.

Replacing wheel bearings

Fig. 12

1.

Remove hub cap pos. 21.

2.

Remove split pin pos. 20.

3.

Remove castle nut pos. 19.

4.

Hub housing can now be removed
from shaft.

5.

Remove bearings pos. 17+18.

6.

Remove seal ring pos. 19.

Assembly

1.

Fit bearing outer rings pos. 17+18 in hub housing pos. 22

2.

Fit seal ring pos. 16.

3.

Fit bearing inner ring pos. 18 on axle pos. 2 and fit axle in hub housing

4.

Fit bearing inner ring pos. 17 on axle pos. 2

5.

Screw castle nut onto axle pos. 2, whilst turning hub housing pos. 22.
Tighten castle nut until hub housing revolves slowly. Slacken castle nut a
quarter turn or until hub housing revolves easily.

6.

Fit split pin pos. 20.

7.

Fill hub cap pos. 21 half full with ball bearing grease and fit to hub

«
...
23
24
25
26
27
...
»

Содержание MAXICUT































Отзывы:

Нет отзывов