DALBO MAXICUT Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 30

DALBO MAXICUT Скачать руководство пользователя страница 13

MAXICUT

Side 13

Connecting and disconnecting

Connecting

Fig.2

MAXICUT  is  attached  to  the  tractor's
lifting  arms  and  secured  using  balls
and split pins (A). The support leg (B)
is  raised  and  secured  by  a  pin  (C).
MAXICUT  200/300  coupled  so  that
the drum section, always preferred to
in paragraph (D).

Remember to secure drawbar with balls and split pins.

Hydraulics

MAXICUT requires a double-acting hydraulic outlet, in which one line is used for
lowering the side sections and other for towing the frame to transport the roller
from field to field.

Table 1. Hose markings

Cylinder name

Colour Outlet

Function

Wheel
frame cylinder

Yellow Double acting

Raises MAXICUT up onto its
wheels and down into working
position.

Extend/retract

Red

Double acting

Retracts

the

sides

up-

wards/downwards.



Check hydraulic hoses for crimping

Disconnection

Fit support leg vertically, release drawbar from tractor and disconnect hydraulic
hoses.

A

B

C

D

«
...
11
12
13
14
15
...
»

Содержание MAXICUT































Отзывы:

Нет отзывов