Daktronics Tuff Sport H-2101 Скачать руководство пользователя

Страница: 22 / 82

Scoreboard Troubleshooting

PanaView

To replace a PanaView digit circuit board (

Figure 9

Open the digit panel as described in

Section

‎

5.2

Disconnect the power/signal connector from the back of the digit by squeezing
together the locking tabs and pulling the connector free.

Use a

" nut driver to remove the nuts securing the digits to the inside of the panel,

and then lift the digit off the stud inserts.

Position a new digit over the studs (making sure the small plastic spacers are still in
place) and tighten the nuts.

Reconnect the power/signal connector.

Note:

This is a keyed connector and it will attach in one way only. Do not attempt to

force the connection.

Secure the digit panel to the display with the two screws, then power up and test the
display to see if changing the digit has resolved the problem.

Figure 9:

PanaView Digit Assembly

Содержание Tuff Sport H-2101



















































































Результаты поиска

Содержание Tuff Sport H-2101

Отзывы:

Похожие инструкции для Tuff Sport H-2101

Бренды по названию

Популярные бренды

Daktronics Tuff Sport H-2101, Руководство пользователя

Результаты поиска

Содержание Tuff Sport H-2101

Отзывы:

Похожие инструкции для Tuff Sport H-2101

Бренды по названию

Популярные бренды