Daktronics ST-2373 Series Скачать руководство пользователя

Страница: 17 / 46

Maintenance & Troubleshooting

Recommended Tools

When performing maintenance work on the display, Daktronics recommends using the

following tools and placing them in a convenient, easy-to-use location.

Tool

Part Number

Use

#2 Phillips screwdriver

TH-1061

Removes rear doors and components on verticals

5/16" T-handle wrench

TH-1088

Engages tabletop latches

5/16" nutdriver

TH-1156

Removes components

11/32" nutdriver

TH-1201

Removes power supplies

These tools are found in the toolkit (0A-1892-0002). The toolkit includes items in addition to

those on the list above, and additional replacement tools may be ordered directly from

Daktronics. Refer to

Daktronics Exchange and Repair & Return Programs (p�18)

Component Location & Access

Scorer’s tables are designed for either front or rear access, depending on site

requirements and customer preference.
While components in front-access displays are simply removed from the front, access

doors in rear-access displays must be removed to reach the internal display components.

Front Access

To access components through the front, refer to

the instructions below and

Figure 18

1�

Disconnect the power to the display.

2�

Lift up the top pad, remove the Phillips head

screws along the top of the protective plex

face panel, and tilt the face panel outward.

Note:

If a possession indicator is attached, it

must be removed before the top pad

can be lifted up. Alternately, an end

pad may be removed to allow the

front face panel to slide out sideways.

Rear Access

To access components through the rear, refer to the instructions below and

Figure 19

1�

Disconnect the power to the display.

2�

Lift the tabletop upward and secure in place as described in

Table Setup (p�4)

3�

Use a #2 Phillips screw-driver (part # TH-1061) to remove the two screws securing the

access door.

4�

Carefully allow the access door to rotate downward into the open position.

Lift up top pad.

Tilt plex face

outward.

Remove Phillips

head screws.

Figure 18:

Front Access

Содержание ST-2373 Series















































Результаты поиска

Содержание ST-2373 Series

Отзывы:

Похожие инструкции для ST-2373 Series

Бренды по названию

Популярные бренды

Daktronics ST-2373 Series, Руководство пользователя

Результаты поиска

Содержание ST-2373 Series

Отзывы:

Похожие инструкции для ST-2373 Series

Бренды по названию

Популярные бренды