manualshive.com logo in svg

Daktronics PROLINK ROUTER 605 Series, Руководство по установке и обслуживанию, Страница: 21 / 54

Поделиться
Скачать
Daktronics PROLINK ROUTER 605 Series Скачать руководство пользователя страница 21

Introduction

17

Indicator Description

DS1

VIN power indicator

DS2

CAN jack transmitter indicator

DS3

Fan jack indicator turns on when voltage is active

DS4

CAN jack indicator toggles with CAN activity

DS5

CAN jack receiver indicator

DS6

ProLink5 Port A transmit indicator

• 

On – port is not configured

• 

Off – port is configured but not transmitting diagnostics

•  Toggling  – port is transmitting diagnostics*

DS7

3.3V power indicator

DS8

2.5V power indicator

DS9

Heartbeat LED

DS10

Error Status LED

DS11-13

Status LEDs 0-2

DS14

ProLink5 Port A receive indicator

•  On – port is not receiving valid signal

•  Off – port is receiving valid signal but not receiving diagnostics

•  Toggling – port is receiving diagnostics*

DS15

ProLink5 Port B transmit indicator

• 

On – port is not configured

• 

Off – port is configured but not transmitting diagnostics

•  Toggling  – port is transmitting diagnostics*

DS16

ProLink5 Port B receive indicator

•  On – port is not receiving valid signal

•  Off – port is receiving valid signal but not receiving diagnostics

•  Toggling – port is receiving diagnostics*

D17

ProLink6 Port A, Channel 0, Indicator L

D18

ProLink6 Port A, Channel 0, Indicator R

D19

ProLink6 Port A, Channel 1, Indicator L

D20

ProLink6 Port A, Channel 1, Indicator R

D21

ProLink6 Port B, Channel 2, Indicator L

D22

ProLink6 Port B, Channel 2, Indicator R

D23

ProLink6 Port B, Channel 3. Indicator L

D24

ProLink6 Port B, Channel 3, Indicator R

* The receive indicator toggles at the rate that the diagnostic requests are received at 

the port. When active, indicators that toggle with received/transmitted diagnostics may 

toggle at a 

1

/

2

 interval, then remain idle for up to 60 seconds.

Содержание PROLINK ROUTER 605 Series























































Отзывы:

Нет отзывов