background image

Controls & Timing Functions

10

Mode #3: Game Clock

Press the 

<START>

 key to start the clock counting down from 

the preset time. Press the 

<STOP>

 key to stop the clock. Press 

the 

<START>

 key to resume the countdown. This procedure 

may be repeated until the clock reaches 0.00. Press 

<RESET/

CLEAR>

 to return the game clock to the original preset time. 

Mode #4: Shot Clock

Press the 

<START>

 key to start the countdown from the preset 

shot clock time. While the clock is running, press the 

<RESET>

 

key to start the clock over again at the preset time and 

automatically start counting down. Press the 

<STOP>

 key to 

pause the countdown. When the clock is stopped, pressing 

<RESET>

 will place the clock at the preset time; however, 

<START>

 must then be pressed to resume the countdown as 

it will not begin automatically. 

Mode #5: 12 Hour Time of Day

To change the time of day, press 

<MENU>

, and then press 

<ENTER>

. Press 

<ENTER>

, input the desired time using the 

keypad, and then press 

<ENTER>

 once more. Select whether 

the time is AM or PM using the arrow keys, and then press 

<ENTER>

 to save the time of day settings. 

Mode #6: 24 Hour Time of Day

To change the time of day, press 

<MENU>

, and then press 

<ENTER>

. Press 

<ENTER>

, input the desired time using the 

keypad, and then press 

<ENTER>

 once more. 

Team Manager

The Daktronics PC-2002 can interface with third-party Hy-Tek™ TEAM MANAGER with 

WORKOUT MANAGER software for easy entry of workouts from a computer to the display. 

The TEAM MANAGER must have the Workout Manager Basic option configured. After 

creating a workout in the Hy-Tek software: 

1� 

Turn on the PC-2002, connect the JC-100 console, and set to mode 

1–WORKOUT

2� 

The interface cable (Daktronics part # 0A-1153-0036) has a 9-pin serial connector on 

one end and a stereo phone jack connector on the other end. Connect the 9-pin 

plug to an available COM port on the Hy-Tek computer. 

Note: 

If the Hy-Tek computer does not have a serial port, a USB-to-serial adaptor 

must be purchased and installed. 

3� 

Plug the stereo phone jack into a J-box (part # 0A-1091-0227). Route minimum 18 

AWG shielded cable (part # W-1117) from the J-box to the 

SIGNAL IN

 terminal block 

on the rear of the display (red to TB-1, black to TB-2).

DWG-195172

 illustrates the connections needed to download information onto the 

PC-2002 from the Hy-Tek software.

4� 

From the TEAM MANAGER main menu, go to 

Workouts > Pace Clock > Daktronics 

Pace Clock

.

5� 

At the top of the Daktronics Pace Clock menu, select the 

Daktronics PC-2000

 button. 

Select the 

Verify

 menu at the top of the screen and enter the serial port number that 

the cable is connected to (most likely 1), and then click 

OK

MENU-CHANGE MODE 

3-GAME CLOCK  {}

GAME CLOCK 15:00 
HORN=AUTO

MENU-CHANGE MODE
4-SHOT CLOCK  {}

SHOT CLOCK 35
HORN=AUTO

MENU-CHANGE MODE 
5-12HR T.O.D. {}

12HR TIME OF DAY
    12:00AM

MENU-CHANGE MODE 
6-24HR T.O.D. {}

24HR TIME OF DAY
    13:00

Содержание PC-2002



































Отзывы: