background image

Eyebolts 

 
Almost every display that leaves Daktronics is equipped with eyebolts for lifting the display. There are 
two standard sizes of eyebolts: ½

 and 

 

Load Increase Factor:

 The load increases as the lift angle (

θ

) decreases. The allowable load on the 

eyebolts also decreases with the lift angle due the bending stress on the eyebolts. In sum, the smaller 
the angle between the cable and the top of the display, the lighter the sign must be to safely lift it. 

Do 

NOT attempt to lift the display when the lift angle is less than 30 degrees. 

W= Weight of sign or Section 

 

H= Distance between top of 

sign and lift point 

 

L= Length of cable on one side 

 

θ

 

= Angle between sign and cable 

 

Horizontal Load 

Angle 

 

 

½” 

” 

Angle Factor 

(L/H)

 

Line Weight/

Line Weight/ 

90 1.00 

 

θ

 

Load

Anchor

Load Anchor 

60 

1.155 

  90

2600 2600 4000 4000 

50 

1.305 

  60

1500 1299 3300 2858 

45 1.414 

 

45

650 

460 

1000 

707 

30 

2.00 

 30

520 260 800 400 

 
 
 

ED7244 Copyright 

©

 1996-2001 

Rev. 4 – 14 March 2001 

Daktronics, Inc.

 

Содержание DistaView BA-1018-31

































































































Отзывы: