background image

Parts Replacement 

19

Section 5:  Parts Replacement

Following is information needed to obtain new parts from Daktronics and how to install them in the display. 

5.1  Replacement Parts List

The following formats may be found on various Daktronics drawings. These 
part numbers can be used when requesting replacement parts from Daktronics 
Customer Service.

Most components within this display carry a label that lists the part number of 
the unit. If as assembly is not listed in the Replacement Parts List below, use the 
label, as shown in 

Figure 15

, to order a replacement. The part number in bold.

0P-1127-0024

SN:  

     2465

02/19/12 Rev. 1

Figure 15: 

Parts Label

Description

Daktronics Part No.

Temperature Sensor

0A-1151-0012

Light and Temperature Sensor

0P-1247-0008

Protocol plug (Protocol-4)

0A-1279-0089

Transformer

T-1072

24 Volt, 150 W DC Power Supply

A-1720

Signal surge suppression board

0P-1110-0011

Driver, 4 Column

0P-1192-0068

DM-100 Controller parts

DM-100 handheld controller

0A-1196-0088

Junction box, outdoor, 9-pin D-male

0A-1196-0093

Junction box, indoor, 9-pin D, male

0A-1196-0099

DM-100 Insert Time & Temp/Gas Price

0G-164998

DM-100 outdoor wired installation kit

0A-1279-0087

DM-100 indoor wired installation kit 

0A-1279-0103

Transformer, wall pack (for DM-100)

T-1118

Cable, serial, DB9 male to DB9 female

W-1267

Digits and Accessories

Digit, 10” red, 7-segment

0A-1192-5120

Digit, 10” amber, 7-segment

0A-1192-5220

Digit, 13” red, 7-segment

0A-1192-5130

Digit, 13” amber, 7-segment

0A-1192-5230

Digit, 18”, red, 7-segment

0A-1192-5140

Digit, 18”, amber, 7-segment

0A-1192-5240

Digit segment, 24” red, vertical

0A-1192-5150

Digit segment, 24” red horizontal

0A-1192-5151

Digit segment, 24” amber, vertical

0A-1192-5250

Digit segment, 24” amber horizontal

0A-1192-5251

Indicator, 1” red (10” and 13” displays)

0A-1611-5133

Indicator, 1” amber (10” and 13” displays)

0A-1611-5233

Indicator, 2” red (18” and 24” displays)

0A-1611-5134

Indicator, 2” amber (18” and 24” displays)

0A-1611-5234

Содержание DataTime DF-1012


















































Отзывы: