MAN# 650369
RANGE
RANGE
RANGE
RANGE
Distance to Empty setup
The range reading will initially show the word
range
until a tank of gas has been driven to allow the gauge to complete its
setup based on your driving. Begin with a full tank of gas and do not refill it until it gets below ¼ tank of gas. This can be done on
multiple trips as long as no fuel is added before it gets low enough. After the initial setup the display will show
r
followed by the
calculated distance to empty. This will count down, making adjustments as necessary, until the range is 35 miles (56km) or less and
then it will show
r Lo
. The gauge will continue to make adjustments to match your driving habits with each fill up. After the initial
setup you are not required to wait for the fuel to get below ¼ tank before refilling.
•
Press and release the switch until “
RANGE
” is displayed, then press and hold the switch until “
-
” is displayed.
•
The display will show “
oFF
” or “
oN
”. Press and release the switch to change to the desired setting.
•
Press and hold the switch until “
-
” is displayed to select the setting.
•
OFF
turns the range display off.
•
Turning the function
on
will access the following menus
o
donE
(exits the setup)
o
rESEt
(resets the gauge to beginning of the initial range learning)
o
sender
(used to change or reset the fuel gauge readings)
Hd
(set to factory default sending unit)
CSt
(set to a custom fuel curve)
•
SET 00
(set new empty reading,
done
indicates it was stored,
error
indicates the signal
is out of range)
•
SET 99
(set new full reading)
•
Press and release the switch to select the desired fuel setup menu, press and hold it until “
-
” is displayed, and then release the
switch to view or go on.
•
A press and hold will save the setting or exit back to the menu.
•
done
is the first menu displayed, a press and hold will exit fuel set up at this point.
•
rESEt
will begin the initial range learning again. You must begin with a full tank of gas and then ride it down to less than ¼ tank.
This can be done in multiple trips as long as the tank is not filled in between. The range display will show
range
until this is
completed and then begin showing the distance to empty.
•
FUL - RESET
This will set the fuel gauge setup points back to stock values.
•
FUL - SET 99
This will set a new full reading for the fuel gauge to allow for customization or improved range accuracy.
done
indicates it was stored,
error
indicates the signal is out of range
•
FUL - SET 00
This will set a new empty reading for the fuel gauge to allow for customization or improved range accuracy.
done
indicates it was stored,
error
indicates the signal is out of range
InFO
InFO
InFO
InFO
Info menu
Displays the current software revision on the speedometer display. (no changes can be done in this menu)
odoMK
odoMK
odoMK
odoMK
Odometer preset
The odometer can be preset by the customer within the first 100 miles. Once the odometer has more than 100 miles, the menu option
will no longer be displayed. Make sure you have correctly selected the units to be either MPH or km/h first. The odometer will be set
in the selected units. The reading shown when entering the preset menu will be the value obtained from the ECM. Once you have
preset the miles you cannot change it again.
WARNING!!: This only allows setting odometer to the nearest mile. Do not use tenths! For example a mileage of 65432.1
should be set to “
065432
” using this method. If the tenths digit is used, the odometer will read 10 times too high.
•
Press and release the switch until “
-odoMK
” is displayed, then press and hold the switch until “
-
” is displayed.
•
The current ECM odometer reading will be displayed with the left most digit flashing.
•
Press and release the switch to increment the digit. Press and hold the switch to move to the next digit to the right.
•
Continue until the right most digit has been set. Press and hold the switch and the speed display will show “
No
”.
•
Press and hold the switch while “
no
” is displayed to go back and continue changing the odometer display. Turn the key off to
cancel any changes.
•
Press and release the switch to change to speed display to “
yes
”. Press and hold the switch while “
yes
” is displayed to save the
current odometer reading.
