Dakota Digital MCL-2011(-R), Руководство пользователя

Страница: 4 / 9

MAN# 650369
SPEEDOMETER SETUP
Press and hold the switch while turning the key on and starting the engine. Once the engine is running, release
the switch. Press and release the switch to change the menu selection.
dIAG dIAG dIAG dIAG Diagnostics mode for checking/clearing trouble codes
•
Press and release the switch until “ dIAG ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The display will show “ ENGINE ”, “ SECvRE ”, ” ABS ”, or “ DoNE ”.
•
Press and release the switch to change the selection, press and hold the switch until “ - ” is displayed to begin reading the stored
codes for the particular system.
•
Release the switch. The display will show the current codes, “ none ”, or “ no rsp ”. Press and release the switch to move to the
next stored code. After all codes are displayed the module part number will be scrolled across the screen. To clear codes, press
and hold the switch when “end” is displayed. Consult a service manual for trouble code descriptions.
SPEED CALIBRATION
The speed calibration is not required unless you have changed out the rear pulley, sprocket, stock transmission, or
stock tires.
ADJvST ADJvST ADJvST ADJvST Adjust speedometer calibration
•
Press and release the switch until “ AdJvSt ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The display will show “ fastEr ” or “ sLOWX ”. Faster will allow you to increase the speedometer reading, slow
will allow you to decrease the speedometer reading.
•
Press and release the switch to change, press and hold the switch to continue. The display will change to “ CL ” and a number from
75 to 125. This is the calibration ratio that is applied to the reading that the ECM is providing. 110 will be 10% faster, 90 will be
10% slower. Think of the number displayed as a percentage.
Actual speed
----------------------------- x current Cal ratio (100 by default) = new Cal ratio
speedometer reading
•
Press and release the switch to change the cal ratio. When the desired cal ratio is shown, press and hold the switch to save it.
vNIT
vNIT vNIT vNIT Speed unit
•
Press and release the switch until “ vnit ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The display will light up the current speed unit (MPH or km/h).
•
Press and hold the switch to keep the current unit or press and release the switch to change the unit.
S SET
S SET S SET
S SET
Miles to Next Service setup
The service mileage is a countdown mile meter. The service mile display can be disabled or can be set to count down from
500 – 7500 miles. If the service mileage is enabled and it gets to 0 miles it will display “ S -DvE ” each time the key is turned on. If the
push button switch is pressed and held while “ S -dve ” or “ S ” and a mileage is displayed, the service miles will be reset to your preset
value.
•
Press and release the switch until “ S set ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The current setting will be displayed, “ OFF ” or a mileage from 500 - 7500 .
•
Press and release the switch until the desired setting is displayed.
•
Press and hold the switch until “ - ” is displayed.
PERF
PERF PERF PERF Performance menu setup
The performance readings can be turned on or off. When they are turned off the message display will only toggle through the
mileage readings.
•
Press and release the switch until “ PErF ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The current setting will be displayed ( on or oFF ).
•
Press and release the switch until the desired setting is displayed.
•
Press and hold the switch until “ - ” is displayed.
nIgHt
nIgHt nIgHt nIgHt Night Dimming
Your display system has a dimming feature that dims the display intensity automatically at night. Normally the system is at full
brightness for daytime viewing. To have the system at full brightness all of the time, go into the setup menu as described above and
select “
ngt ” (night). Press and release the trip switch to select “ OFF ” instead of “ on ”. Press and hold the trip switch to save the new
setting.
•
Press and release the switch until “ nIgHt ” is displayed, then press and hold the switch until “ - ” is displayed.
•
Release the switch. The current setting will be displayed. ( ON , OFF ).
•
Press and release the switch until the desired setting is displayed.
•
Press and hold the switch until “ - ” is displayed to save the setting.