MAN #650500F
Display data usage
The RPM, speed, and engine temperature can each be used in place of connections to the instrument control unit. These
are individually selectable in the instrument system setup menus.
The transmission gear position will be displayed in the message center if it is available. This will automatically be
displayed whenever the gear changes. If a GSS universal gear position sender is connected, the GSS will override the
BIM-01-2 data.
The malfunction indicator lamp (MIL) or service engine soon indicator will be activated from the data bus when there is an
engine code set. This will not turn on the indicator for a lamp test function when the key is on, but the engine is not
running. This indicator can be enabled or disabled in the BIM-01-2 setup. Some gauge features require a minimum
software revision or higher to be supported:
Engine Indicator
Oil Pressure & Fuel Level
VHX
VX03
VX04
VFD3
SE45
SE47
VFD3X
SE54
SE55
The intake air temp, transmission temp, and ambient air temp will be displayed in the message center.
VFD3 Setup:
Using speed from the BIM-01-2
•
Hold the SW1 switch from the instrument system control box while turning the key on. The message display
should show SETUP.
•
Release SW1. The message display should show
SPEED.
•
Press and hold SW1 for at least 3 seconds and then release it. The message display should show
SENDER.
•
Press and hold SW1 for at least 3 seconds and then release it. The display should show the current setting.
•
Press and release SW1 until
BUS is displayed.
•
Press and hold SW1 until DONE is displayed.
Using RPM from the BIM-01-2
•
Hold the SW1 switch from the instrument system control box while turning the key on. The message display
should show SETUP.
•
Release SW1. Press and release SW1 until
TACH is displayed.
•
Press and hold SW1 for at least 3 seconds and then release it. The display should show
T CAL.
•
Press and hold SW1 for at least 3 seconds and then release it. The display should show the current setting.
•
Press and release SW1 until
T CAL is displayed.
•
Press and hold SW1 until DONE is displayed.
Using engine temperature from the BIM-01-2
•
Hold the SW1 switch from the instrument system control box while turning the key on. The message display
should show SETUP.
•
Release SW1. Press and release SW1 until
WATER is displayed.
•
Press and hold SW1 for at least 3 seconds and then release it. The message display should show
SENDER.
•
Press and hold SW1 for at least 3 seconds and then release it. The display should show the current setting.
•
Press and release SW1 until
BUS F or
BUS C is displayed depending on your unit choice.
•
Press and hold SW1 until DONE is displayed.
Using oil pressure from the BIM-01-2 (if available)
•
Hold the SW1 switch from the instrument system control box while turning the key on. The message display
should show SETUP.
•
Release SW1. Press and release SW1 until
OIL is displayed.
•
Press and hold SW1 for at least 3 seconds and then release it. The message display should show
SENDER.
•
Press and hold SW1 for at least 3 seconds and then release it. The display should show the current setting.
•
Press and release SW1 until
BUS is displayed.
•
Press and hold SW1 until DONE is displayed.
Using fuel level from the BIM-01-2 (if available)
•
Hold the SW1 switch from the instrument system control box while turning the key on. The message display
should show SETUP.
•
Release SW1. Press and release SW1 until
FUEL is displayed.
•
Press and hold SW1 for at least 3 seconds and then release it. The message display should show
SENDER.
•
Press and hold SW1 for at least 3 seconds and then release it. The display should show the current setting.
•
Press and release SW1 until
BUS is displayed.
•
Press and hold SW1 until DONE is displayed.
