background image

Dakota Alert, Inc.

www.

dakotaalert

.com

Phone:

 (605) 356-2772

Fax:

 (605) 356-3662

Address:

 32556 477th Ave.   |  P0 Box 130  |  Elk Point, SD 57025

19-0041 

Dakota Alert

®

WIRELESS SECURITY EQUIPMENT

TM

WARRANTY

Dakota Alert warrants this product to be free of defects in materials and workmanship for a period of one year from 
the date of purchase. This warranty does not cover damage resulting from accident, abuse, act of God, or improper 
operation. If this product does become defective, simply return it to Dakota Alert. Please include a note describing 
the troubles along with your name and return address as well as the original sales receipt. If the product is covered 
under the warranty it will be repaired or replaced at no charge. If it is not covered by the warranty, you will be 
notifi ed of any charges before work is done.

LEGAL NOTICES

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this 
device may not cause harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation. Changes or modifi cations not expressly approved by the party 
responsible for compliance could void the user’s authority to operate the equipment. This equipment has been 
tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance 
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off  and on, the user is encouraged to try 
to correct the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

 

WARNING: 

Cancer and Reproductive Harm. Go to 

www.P65Warnings.ca.gov

 for more information.

BBT-4000_19-0041_MAN.indd   8

BBT-4000_19-0041_MAN.indd   8

2/4/2019   9:47:08 AM

2/4/2019   9:47:08 AM

Содержание BBT-4000









Отзывы: