background image

13 Unit installation

Installation and operation manual

16

RWEYQ8~14T9Y1B

VRV IV water-cooled system air conditioner

4P452190-1D – 2020.10

g

Boiler

13

Unit installation

13.1

Preparing the installation site

13.1.1

Installation site requirements of the
outdoor unit

Mind the spacing guidelines. See the "Technical data" chapter.

CAUTION

Appliance not accessible to the general public, install it in a
secured area, protected from easy access.

This  unit,  both  indoor  and  outdoor,  is  suitable  for
installation 

in 

commercial 

and 

light 

industrial

environment.

NOTICE

This  equipment  is  compliant  with  Class  A  of  EN55032/
CISPR  32.  In  a  residential  environment  this  equipment
may cause radio interference.

13.2

Opening the unit

13.2.1

To open the outdoor unit

DANGER: RISK OF ELECTROCUTION

DANGER: RISK OF BURNING/SCALDING

11×

A

B

Once the front plate A is open, the electrical component box can be
accessed. See 

"13.2.2 To open the electrical component box of the

outdoor unit"

 [

4

 16].

For service purposes, the pushbuttons on the main PCB need to be
accessed.  To  access  these  pushbuttons,  the  electrical  component
box  cover  does  not  need  to  be  opened.  See 

"16.1.3  To  access  the

field setting components"

 [

4

 32].

To  install  the  water  piping  and  field  wiring,  front  plate  B  has  to  be
removed.

13.2.2

To open the electrical component box of
the outdoor unit

NOTICE

Do  NOT  apply  excessive  force  when  opening  the
electronic  component  box  cover.  Excessive  force  can
deform  the  cover,  resulting  in  entering  of  water  to  cause
equipment failure.

SW8

2

1

13.3

Mounting the outdoor unit

13.3.1

To provide the installation structure

Make  sure  the  unit  is  installed  level  on  a  sufficiently  strong  base  to
prevent vibration and noise.

800 mm

600 mm

516 mm

480 mm

660 mm

a

▪ Fasten the unit in place using four foundation bolts M12. It is best

to  screw  in  the  foundation  bolts  until  their  length  remains  20  mm
above the foundation surface.

20 mm

14

Piping installation

14.1

Preparing refrigerant piping

14.1.1

Refrigerant piping requirements

NOTICE

Refrigerant  R410A  requires  strict  cautions  for  keeping  the
system clean and dry. Foreign materials (including mineral
oils  or  moisture)  should  be  prevented  from  getting  mixed
into the system.

NOTICE

The  piping  and  other  pressure-containing  parts  shall  be
suitable  for  refrigerant.  Use  phosphoric  acid  deoxidised
seamless copper for refrigerant.

▪ Foreign materials inside pipes (including oils for fabrication) must

be ≤30 mg/10 m.

▪ Temper  grade:  use  piping  with  temper  grade  in  function  of  the

pipe diameter as listed in table below.

Pipe Ø

Temper grade of piping material

≤15.9 mm

O (annealed)

Содержание VRV IV RWEYQ-T9









































Отзывы: