background image

3P362438-1B English

i

Safety considerations

Read these Safety considerations for Installation carefully be-
fore installing an air conditioner or heat pump. After complet-
ing the installation, make sure that the unit operates properly 
during the startup operation.
Instruct the customer on how to operate and maintain the 
unit.
Inform customers that they should store this Installation 
Manual with the Operation Manual for future reference.
Always use a licensed installer or contractor to install this 
product.
Improper installation can result in water or refrigerant leak-

age, electrical shock, fire, or explosion.

Meanings of 

DANGER

WARNING

CAUTION

, and 

NOTE

Symbols:

DANGER   .  .  .  .  .  .  .  .

Indicates an imminently hazardous 
situation which, if not avoided, will 
result in death or serious injury.

WARNING   .  .  .  .  .  .  .

Indicates a potentially hazardous 
situation which, if not avoided, 
could result in death or serious 
injury.

CAUTION  .  .  .  .  .  .  .  .

Indicates a potentially hazardous 
situation which, if not avoided, 
may result in minor or moderate 
injury. It may also be used to alert 
against unsafe practices.

NOTE   .  .  .  .  .  .  .  .  .  .  .

Indicates situations that may result 
in equipment or property-damage 
accidents only.

INFORMATION   .  .  .

This symbol identifies useful tips 

or additional information.

 DANGER

•  Refrigerant gas is heavier than air and replaces oxygen. A 

massive leak will result in oxygen depletion, especially in 
basements, and an asphyxiation hazard will result in seri

-

ous injury or death.

• 

Do not ground units to water pipes, gas pipes, telephone 
wires, or lightning rods as incomplete grounding will result 
a severe shock hazard resulting in severe injury or death. 
Additionally, grounding to gas pipes will result a gas leak 

and potential explosion resulting in severe injury or death.

• 

If refrigerant gas leaks during installation, ventilate the 
area immediately. Refrigerant gas will result in producing 

toxic gas if it comes into contact with fire. Exposure to this 

gas will result in severe injury or death.

• 

After completing the installation work, check that the re-
frigerant gas does not leak throughout the system.

•  Do not install unit in an area where flammable materials 

are present due to risk of explosions that will result in seri

-

ous injury or death.

• 

Safely dispose all packing and transportation materials 
in accordance with federal/state/local laws or ordinances. 
Packing materials such as nails and other metal or wood 
parts, including plastic packing materials used for trans-
portation will result in injuries or death by suffocation.

 WARNING

•  Only qualified personnel must carry out the installation 

work. Installation must be done in accordance with this 
installation manual. Improper installation could result in 

water leakage, electric shock, or fire.

• 

When installing the unit in a small room, take measures to 

keep the refrigerant concentration from exceeding allow

-

able safety limits. Excessive refrigerant leaks, in the event 

of an accident in a closed ambient space, could result in 

oxygen deficiency.

•  Use only specified accessories and parts for installation 

work. Failure to use specified parts could result in water 
leakage, electric shocks, fire, or the unit falling.

• 

Install the air conditioner or heat pump on a foundation 
strong enough that it can withstand the weight of the unit. 

A foundation of insufficient strength could result in the unit 

falling and causing injuries.

• 

Take into account strong winds, typhoons, or earthquakes 
when installing. Improper installation could result in the 
unit falling and causing accidents.

• 

Make sure that a separate power supply circuit is pro-
vided for this unit and that all electrical work is carried 

out by qualified personnel according to local, state and 
national regulations. An insufficient power supply capacity 

or improper electrical construction could result in electric 

shocks or fire.

•  Make sure that all wiring is secured, that specified wires 

are used, and that no external forces act on the terminal 

connections or wires. Improper connections or installation 

could result in fire.

•  When wiring, position the wires so that the control box 

cover can be securely fastened. Improper positioning of 

the control box cover could result in electric shocks, fire, or 

the terminals overheating.

• 

Before touching electrical parts, turn off the unit. 

• 

This equipment can be installed with a Ground-Fault Cir-
cuit Breaker (GFCI). Although this is a recognized mea-
sure for additional protection, with the grounding system in 
North America, a dedicated GFCI is not necessary.

• 

Securely fasten the unit terminal cover (panel). If the 
terminal cover/panel is not installed properly, dust or 

water may enter the outdoor unit and could result in fire or 

electric shock.

• 

When installing or relocating the system, keep the refriger-

ant circuit free from substances other than the specified 

refrigerant (R410A) such as air. Any presence of air or oth-
er foreign substance in the refrigerant circuit could result 
in abnormal pressure rise or rupture, resulting in injury.

• 

Do not change the setting of the protection devices. If the 
pressure switch, thermal switch, or other protection device 
is shorted and operated forcibly, or parts other than those 

specified by Daikin are used, fire or explosion could result.

Содержание RXYQ120TTJU


















































Отзывы: