background image

5 Installation

Installation manual 

34

RWEQ96~432TAYD

 + RWEQ96~432TATJ

 

VRV W T-Series water-cooled system air conditioner

The power supply wiring can be routed from the front side. Exit the 

wiring via the upper mounting hole.

A1P

5 .8 .7

To connect the power supply

NOTE 

Never connect the power supply to transmission wiring 

terminal block. Otherwise the entire system may break 

down.

CAUTION 

When connecting the power supply, the ground connection 

must be made before the current-carrying connections are 

established. When disconnecting the power supply, the 

current-carrying connections must be separated before the 

ground connection is. The length of the conductors 

between the power supply stress relief and the terminal 

block itself must be as such that the current-carrying wires 

are tautened before the ground wire is in case the power 

supply is pulled loose from the stress relief.

Tightening torque for the terminal screws:

Screw size

Tightening torque

M8 (Power terminal block)

4.05~5.38 ft·lbf (5.5~7.3 N·m)

M8 (Ground)

NOTE 

Recommendations when connecting the ground wire:
Wire it so that it comes through the cut out section of the 

cup washer. (An improper ground connection may prevent 

a good grounding from being achieved.)

The power supply must be clamped to the plastic bracket using field 

supplied clamp material.
The green and yellow striped wire must be used for grounding only 

(refer to the figure below).

d

h

e

b

a

c

g

i

d

f

a

Power supply (208/230 V - 3 phase 60 Hz 

OR

 460 V - 3 

phase 60 Hz)

b

Fuse or circuit breaker

c

Ground wire

d

Power supply terminal block

e

Connect each power wire: RED to L1, WHT to L2 and BLK 

to L3

f

Ground wire (GRN/YLW). When connecting the ground 

wire, it is recommended to perform curling.

g

Clamp the power supply to the bracket using a field 

supplied clamp to prevent external force being applied to 

the terminal.

h

Cup washer.

i

Vinyl tube (accessory)

5 .8 .8

To connect the conduit

Power supply and transmission wiring: Connect it using 

conduit mounting plates .

Conduit (field supply) 

Conduit 

mounting 

plate 

(accessory)

Lock nut (field supply) 

Top plate

Top plate

5 .8 .9

To connect the optional wiring

For the optional wiring use insulated wires of a rated voltage of 

250 V or higher and a minimal cross section of AWG16 for single 

core wires and AWG18 for multicore wires.

Variable water flow

The variable water flow output signal is a low voltage control signal 

which generates an output of 2~9 V DC depending on the required 

water flow rate through the plate heat exchanger. For more 

information, see "4.4.4 Variable water flow rate" on page 18.

NOTE 

The maximum output power of the 2~9 V DC output signal is 

50 mW. Exceeding this power can result in damage of the system.
Always use shielded cables with a minimal cross section of 

AWG18 and a length limited to 328 ft (100 m).

The control line of the valve/pump should be connected to the X2M 

connector in the electrical switchbox. To connect the valve/pump to 

the outside unit, also provide a separate 12 V DC power supply (to 

be installed external of outside unit) (with an output power of at least 

50 mW) to the X2M connector.
Connect the valve/pump to: X2M terminals 2 and 3.

01_EN_4P602454-1C.indd   34

2020/07/29   16:16:49

Содержание RWEQ96TAYD Series






















































Отзывы: