![background image](http://html2.mh-extra.com/html/daikin/roofpak-rps-series/roofpak-rps-series_installation-and-maintenance-manual_5694134111.webp)
Maintenance and Service
www.DaikinApplied.com 111
IM 926-3 • ROOFPAK APPLIED SYSTEMS
Propeller Exhaust
Propeller Exhaust Fan Option on page
Vibration Levels
Each unit as shipped is trim balanced to operate smoothly. To
provide satisfactory operation after shipping and installation,
use accepted industry guidelines for field balancing fans. See
NOTE:
Excessive vibration from any cause contributes
to premature fan and motor bearing failure.
Monitor overall vibration levels every six months of
operation. An increase in levels is an indication of
potential trouble.
Table 29: Vibration Levels
Fan speed (RPM)
Vibration
800 or less
5 mils maximum displacement
801 or greater
0.20 in/sec maximum velocity
Vibration Causes
1. Wheel imbalance.
a. Dirt or debris on wheel blades.
b.
Loose setscrews in wheel hub or bearing-to-shaft.
c.
Wheel distorted from overspeed.
2.
Bent shaft.
3.
Faulty drive.
a.
Variable pitch sheaves—Axial and radial runout of
flanges; uneven groove spacing; out of balance.
Also similar faults in driven sheave.
b.
Bad V-belts; lumpy, or mismatched; belt tension
too tight or too loose.
4. Bad bearings, loose bearing hold-down bolts.
5. Motor imbalance.
6.
Fan section not supported evenly on foundation.
Periodic Service and Maintenance
1.
Check all moving parts for wear every six months.
2. Check bearing collar, sheave, wheel hub setscrews,
sheave capscrews, and bearing hold-down bolts for
tightness every six months.
Setscrews
Setscrews are used to lock bearings, sheaves, locking
collars, and fan wheels to their shafts. They must be checked
periodically to see that they have not loosened. If this is not
done, severe equipment damage could occur.
and check the tightness of all setscrews with
a torque wrench. Note that if the return fan bearings setscrews
must be retightened, a special procedure is required to equally
).
Table 30: Setscrew Minimum Torque Specifications
Setscrew diameter (in .)
Minimum torque (ft .lb .)
1/4
5.5
5/16
10.5
3/8
19.0
7/16
29.0
1/2
42.0
5/8
92.0
Return Fan Bearing Setscrews
Because the return fan is mounted on a vertical shaft, the
following procedure must be used to retighten any return fan
bearing setscrews that have loosened. This procedure will
provide that both bearings are equally loaded. If one bearing is
carrying the entire weight of the fan, it could fail prematurely.
1.
Loosen the fan belts.
2.
Support the weight of the fan and the fan shaft with
timbers or some other suitable means (see the fan shaft
support in
). Important: To maintain proper
drive alignment and fan-to-tunnel clearance, the fan
and shaft must not drop at all when the setscrews are
loosened in Step 4.
3.
Verify that the upper shaft collar is securely fastened to
the shaft. Check the setscrew torque.
4. Loosen the upper and lower bearing setscrews. The
entire weight of the fan and shaft is now supported by
the fan shaft support.
5. Retighten all bearing setscrews to the torque
specification given in
support and re-tension the belts.
Figure 121: Return Fan Assembly
Содержание RoofPak RPS Series
Страница 71: ...Wiring Diagrams www DaikinApplied com 71 IM 926 3 ROOFPAK APPLIED SYSTEMS Figure 87 VFD Control SAF and RAF...
Страница 72: ...IM 926 3 ROOFPAK APPLIED SYSTEMS 72 www DaikinApplied com Wiring Diagrams Figure 88 VAV Control Inputs...
Страница 76: ...IM 926 3 ROOFPAK APPLIED SYSTEMS 76 www DaikinApplied com Wiring Diagrams Figure 90 Electric Heat Control...
Страница 129: ......