Daikin MC70LPVM Скачать руководство пользователя страница 16

15

Quick Reference Table of Maintenance

Before performing maintenance, stop the unit and disconnect the power plug. (It may cause electric shock or injury.)

WARNING

Remove the parts for maintenance in numerical order.

For details on removing and attaching each part, see 

Page 17.

 

 .

1

Front panel

2

Pre

fi

 lter

3

UNIT1

(Plasma ioniser)

4

UNIT2

(Streamer unit)

The 

fi

 gure above shows 

UNIT1 after the opposing 

pole plates are removed.

If it gets dirty

Wipe

About once every 2 weeks

Vacuum cleaner

Rinse with water

If the “UNIT1” 

lamp lights

Soak, drain and dry

Wipe

Once every 3 months or if 

the “UNIT2” lamp lights

Soak, drain and dry

Wipe

Wipe off the dirt with a cloth 

• 

slightly moistened with water.
In the case of heavy dirt, wipe it 

• 

off with a cloth moistened with 
neutral detergent.
Do not use hard brushes, etc.

• 

Use a vacuum cleaner to 

• 

remove the dust from the 
pre

fi

 lter, and wash it with water.

In the case of heavy dirt, wash 

• 

the pre

fi

 lter with a soft brush or 

neutral detergent and dry it well 
in the shade.

Dry the pre

fi

 lter completely before 

using it because the “UNIT1” lamp 
may light up if any water drops 
remain on the pre

fi

 lter.

Use a vacuum cleaner to remove the dust.

• 

Soak in lukewarm water or water. (About 1 hour)

• 

Dry throughly after soaking.

• 

Care and Cleaning 

Page 19, 20.

 

Ionised wire

Ionising frame

Opposing pole plates

NOTE

When detergent is used, wipe the detergent off the surface to 

• 

prevent any residue.
Do not dry the pre

fi

 lter in a place exposed to direct sunlight.

• 

Do not use hot water with a temperature of 50°C or higher for 

• 

cleaning the parts.
Do not dry the parts over a 

fi

 re.

• 

It may cause discolouration or deformation of the parts and the 
parts may become unusable.

Do not use gasoline, benzene, thinner, scouring powder, 

• 

kerosene, alcohol, etc.
(Cracking, electric shock or 

fi

 re may occur.)

Do not wash the main unit with water.

• 

(Electric shock, 

fi

 re or malfunction may occur.)

WARNING

01_EN_3P276413-3C.indd   15

01_EN_3P276413-3C.indd   15

9/27/2011   1:27:02 PM

9/27/2011   1:27:02 PM

Содержание MC70LPVM





























Отзывы: