background image

16 Configuration

Installation and operation manual

20

FXFA20~125A2VEB

VRV system air conditioner

3P599604-1C – 2020.10

▪ For all-round airflow, use the table below.

If the distance to the floor is (m)

Then

(1)

M

SW

≤2.7

13 (23)

0

01

2.7<x≤3.0

02

3.0<x≤3.5

03

Setting: Decoration panel type

When  installing  or  changing  the  decoration  panel  type,  ALWAYS
check if the correct values are set.

If the … decoration panel is used

Then

(1)

M

SW

Standard or self-cleaning

13 (23)

15

01

Design

02

Setting: Airflow direction range

This setting must correspond with the needs of the user.

If you want set the airflow direction

range to…

Then

(1)

M

SW

Upper

13 (23)

4

01

Medium

02

Lower

03

Setting: Air volume when thermostat control is OFF

This  setting  must  correspond  with  the  needs  of  the  user.  It
determines  the  fan  speed  of  the  indoor  unit  during  thermostat  OFF
condition.

1

If you have set the fan to operate, set the air volume speed:

If you want…

Then

(1)

M

SW

During thermostat
OFF at cooling
operation

LL

(2)

12 (22)

6

01

Setup volume

(2)

02

OFF

(a)

03

Monitoring 1

(2)

04

Monitoring 2

(2)

05

Monitoring 3

(2)

06

H

(2)

07

During thermostat
OFF at heating
operation

LL

(2)

12 (22)

3

01

Setup volume

(2)

02

OFF

(a)

03

Monitoring 1

(2)

04

Monitoring 2

(2)

05

Monitoring 3

(2)

06

H

(2)

07

(a)

Only use in combination with optional remote sensor or when
setting 

M

 10 (20), 

SW 

2, —

 

3 is used.

Setting: Time to clean air filter

This setting must correspond with the air contamination in the room.
It determines the interval at which 

"Time to clean filter"

 notification

is displayed on the user interface.

If you want an interval of…

(air contamination)

Then

(1)

M

SW

±2500 h (light)

10 (20)

0

01

±1250 h (heavy)

02

Notification ON

3

01

Notification OFF

02

Setting: Thermostat sensor selection

This  setting  must  correspond  with  how/if  the  remote  controller
thermostat sensor is used.

When the remote controller thermostat

sensor is…

Then

(1)

M

SW

Used in combination with indoor unit
thermistor

10 (20)

2

01

Not used (indoor unit thermistor only)

02

Used exclusively

03

Setting: Thermostat differential changeover (if remote sensor is
used)

If  the  system  contains  a  remote  sensor,  set  the  increase/decrease
increments.

If you want to change increments to…

Then

(1)

M

SW

1°C

12 (22)

2

01

0.5°C

02

Setting: Differential for automatic changeover

Set  temperature  difference  between  cooling  setpoint  and  heating
setpoint  in  automatic  mode  (availability  depends  on  the  system
type). Differential is cooling setpoint minus heating setpoint.

(1)

Field settings are defined as follows:

M

: Mode number – 

First number

: for group of units – 

Number between brackets

: for individual unit

SW

: Setting number

• —: Value number

: Default

(2)

Fan speed:

LL

: Low fan speed (set during thermostat OFF)

L

: Low fan speed (set by the user interface)

H:

 High fan speed

Setup volume

: The fan speed corresponds to the speed the user has set (low, medium, high) using the fan speed button on the user

interface.

Monitoring 1, 2, 3

: The fan is OFF, but runs for a short time every 6 minutes to detect the room temperature by 

LL

 (Monitoring 1), by 

L

(Monitoring 2) or by 

H

 (Monitoring 3).

Содержание FXFA100A2VEB

























Отзывы: