background image

12 Unit installation

Installation and operation manual

14

FXFA20~125A2VEB

VRV system air conditioner

3P599604-1C – 2020.10

A

Minimum distance to the wall (see below)

B

Minimum and maximum distance to the floor (see below)

C

20~63 class:

224 mm:

 In case of installation with standard decoration

panel

266 mm:

 In case of installation with design decoration

panel

304 mm:

 In case of installation with self-cleaning

decoration panel

274 mm:

 In case of installation with fresh air intake kit

80~100 class:

266 mm:

 In case of installation with standard decoration

panel

308 mm:

 In case of installation with design decoration

panel

346 mm:

 In case of installation with self-cleaning

decoration panel

316 mm:

 In case of installation with fresh air intake kit

125 class:

308 mm:

 In case of installation with standard decoration

panel

350 mm:

 In case of installation with design decoration

panel

388 mm:

 In case of installation with self-cleaning

decoration panel

358 mm:

 In case of installation with fresh air intake kit

a

Indoor unit

b

Lighting (the figure shows ceiling-mounted lighting, but
recessed lighting is also allowed)

c

Air fan

d

Static volume (example: table)

A:  Minimum  distance  to  the  wall

.  Depends  on  the  air  flow

directions towards the wall.

≥1500

≥500

≥200

a

A

A

A

b

c

a

Air outlet and corners open

b

Air outlet closed, corners open (optional blocking pad kit
required)

c

Air outlet and corners closed (optional blocking pad kit
required)

B: Minimum and maximum distance to the floor

:

▪ Minimum: 2.7 m to avoid accidental touching.

▪ Maximum: Depends on the air flow directions and the capacity

class.  Also  make  sure  the  "Ceiling  height"  field  setting
corresponds  with  the  actual  situation.  See 

"16.1  Field

setting" 

[

4

 19].

If air flow direction…

Then B

FXFA20~100

FXFA125

All-round

≤3.5 m

≤4.2 m

4-way

(a)

≤4.0 m

≤4.5 m

3-way

(a)

≤3.5 m

≤4.2 m

(a)

Optional blocking kit required

INFORMATION

Some options may require additional service space. Refer
to  the  installation  manual  of  the  used  option  before
installation.

Minimum floor area requirements

CAUTION

The  total  refrigerant  charge  in  the  system  cannot  exceed
the  requirements  for  minimum  floor  area  of  the  smallest
room that is served. For minimum floor area requirements
for  indoor  units,  see  the  installation  and  operation  manual
of the outdoor unit.

12.2

Mounting the indoor unit

12.2.1

Guidelines when installing the indoor unit

INFORMATION

Optional  equipment.

  When  installing  optional  equipment,

also read the installation manual of the optional equipment.
Depending  on  the  field  conditions,  it  might  be  easier  to
install the optional equipment first.

Decoration  panel

.  Install  the  decoration  panel  always 

after

installing the unit.

NOTICE

After installing the decoration panel:

▪ Make  sure  there  is  no  gap  between  the  unit  body  and

the  decoration  panel. 

Possible  consequence: 

Air

might leak and cause dew drop.

▪ Make  sure  no  oil  remains  on  the  plastic  parts  of  the

decoration 

panel. 

Possible 

consequence:

Degradation and damage of plastic parts.

Ceiling  strength

.  Check  whether  the  ceiling  is  strong  enough  to

support the weight of the unit. If there is a risk, reinforce the ceiling
before installing the unit.

▪ For existing ceilings, use anchors.

▪ For  new  ceilings,  use  sunken  inserts,  sunken  anchors  or  other

field supplied parts.

A

c

b

d
e

a

A

50~100 mm

: In case of installation with standard panel

100~150 mm

: In case of installation with fresh air intake

kit or design panel

130~180 mm

: In case of installation with self-cleaning

decoration panel

a

Ceiling slab

b

Anchor

c

Long nut or turnbuckle

d

Suspension bolt

e

Suspended ceiling

Suspension bolts.

 Use M8~M10 suspension bolts for installation.

Attach  the  hanger  bracket  to  the  suspension  bolt.  Fix  it  securely
using  a  nut  and  washer  from  the  upper  and  lower  sides  of  the
hanger bracket.

(mm)

780

710

a1

b

b

a2

c

a1

Nut (field supply)

a2

Double nut (field supply)

b

Washer (accessories)

c

Hanger bracket (attached to the unit)

Paper  pattern  for  installation 

(upper  part  of  the  packing).  Use

the paper pattern to determine the correct horizontal positioning. It
contains  the  necessary  dimensions  and  centers.  You  can  attach
the paper pattern to the unit.

Содержание FXFA100A2VEB

























Отзывы: