Daikin FTXS35K2V1B Скачать руководство пользователя страница 97

Страница: 97 / 130

SiBE041213E

Troubleshooting

Service Diagnosis

Troubleshooting

In case of “

” “

”

: Outdoor temperature thermistor

: Discharge pipe thermistor

: Outdoor heat exchanger thermistor

Check No.01

Refer to P.92

(R16059)

Caution

YES

Turn on the power again.

Normal?

Reconnect the connectors
or thermistors.

error: the discharge

pipe temperature is
lower than the heat
exchanger temperature.

Replace the defective
thermistor(s) of the following
thermistors.

∗

Outdoor temperature

thermistor

∗

Discharge pipe thermistor

∗

Outdoor heat exchanger

thermistor

Cooling: Outdoor heat

exchanger
temperature

Heating: Indoor heat

exchanger
temperature

Replace the indoor heat
exchanger thermistor.

Replace the outdoor unit
PCB.

Error displayed

again on remote

controller?

Indoor heat

exchanger thermistor

functioning?

Check No. 01

Check the thermistor resistance
value.

Check No. 01

Check the indoor heat exchanger
thermistor resistance value in the
heating operation.

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

Содержание FTXS35K2V1B



































































































































Результаты поиска

Содержание FTXS35K2V1B

Отзывы:

Daikin FTXS35K2V1B, Руководство по обслуживанию, Страница: 97 / 130

Результаты поиска

Содержание FTXS35K2V1B

Отзывы: