Daikin FTXS35K2V1B Скачать руководство пользователя страница 109

Страница: 109 / 130

SiBE041213E

Check

Service Diagnosis

5.9

Installation Condition Check

Check No.17

5.10 Discharge Pressure Check

Check No.18

Installation condition check

Check the allowable

dimensions of the air

suction and

discharge area.

Is the airflow blocked by

obstacles or winds

blowing in the opposite

direction?

(R17537)

YES

Is the discharged air

short-circuited?

Is the outdoor heat

exchanger very dirty?

Change the installation
location or direction.

Clean the outdoor heat
exchanger.

Change the installation
location or direction.

Check the outdoor temperature.
(The outdoor temperature
should be within the operation
range.)

(R15738)

Not dirty

YES

Dirty

YES

Is the air

filter or indoor / outdoor

heat exchanger

dirty?

Is the connection pipe

deformed?

Is the stop valve open?

High?

Replace the compressor.

Open the stop valve.

Replace the pipe installed at
the site.

Clean the dirty air filter or
indoor / outdoor heat
exchanger.

Replace the compressor.

Discharge pressure check

Содержание FTXS35K2V1B



































































































































Результаты поиска

Содержание FTXS35K2V1B

Отзывы:

Daikin FTXS35K2V1B, Руководство по обслуживанию, Страница: 109 / 130

Результаты поиска

Содержание FTXS35K2V1B

Отзывы: