Daikin FTXS35K2V1B Скачать руководство пользователя страница 96

Страница: 96 / 130

Troubleshooting

SiBE041213E

Service Diagnosis

4.21 Thermistor or Related Abnormality (Outdoor Unit)

Error Code

Method of Error
Detection

This fault is identified based on the thermistor input voltage to the microcomputer.
A thermistor fault is identified based on the temperature sensed by each thermistor.

Error Decision
Conditions

The thermistor input voltage is above 4.96 V or below 0.04 V with the power on.

error is judged if the discharge pipe temperature is lower than the heat exchanger

temperature.

Supposed
Causes

Disconnection of the connector for the thermistor

Thermistor corresponding to the error code is defective

Defective heat exchanger thermistor in the case of

error (outdoor heat exchanger

thermistor in cooling operation, or indoor heat exchanger thermistor in heating operation)

Defective outdoor unit PCB

Troubleshooting

In case of “

”

Replace the outdoor unit PCB.

: Radiation fin thermistor

Caution

Be sure to turn off the power switch before connecting or disconnecting
connectors, or parts may be damaged.

Содержание FTXS35K2V1B



































































































































Результаты поиска

Содержание FTXS35K2V1B

Отзывы:

Daikin FTXS35K2V1B, Руководство по обслуживанию, Страница: 96 / 130

Результаты поиска

Содержание FTXS35K2V1B

Отзывы: