background image

English

5

English

Indoor Unit Installation

1.

Installing the mounting plate

• The mounting plate should be installed on a wall which can support the weight of the indoor unit.
1) Temporarily secure the mounting plate to the wall, make sure that the panel is completely level, and mark the boring points 

on the wall.

2) Secure the mounting plate to the wall with screws.

Recommended mounting plate retention spots and dimensions

2.

Boring a wall hole and installing wall embedded pipe

• For walls containing metal frame or metal board, be sure to use a wall 

embedded pipe and wall cover in the feed-through hole to prevent possible 
heat, electrical shock, or fire.

• Be sure to caulk the gaps around the pipes with caulking material to 

prevent water leakage.

1) Bore a feed-through hole of 65mm in the wall so it has a down slope 

toward the outside.

2) Insert a wall pipe into the hole.
3) Insert a wall cover into wall pipe.
4) After completing refrigerant piping, wiring, and drain piping, caulk pipe hole gap with putty.

3.

Installing the indoor unit

• In the case of bending or curing refrigerant pipes, keep the following 

precautions in mind.
Abnormal sound may be generated if improper work is conducted.

1) Do not strongly press the refrigerant pipes onto the bottom frame.
2) Do not strongly press the refrigerant pipes on the front grille, either.

209

241

191.5

66

106

176

150

384

900

344

75.5

48

250

48

298

50

50

Use a tape measure 
as shown.

unit: mm

Removed pipe 
port cover 

Recommended mounting plate 
retention spots (5 spots in all)

Place a leveler 
on raised tab.

Drain hose position

Keep here the piece cut out 
from the unit for piping

Liquid pipe end

Gas pipe end

Mounting plate

* The removed pipe port cover can be 

kept in the mounting plate pocket.

Position the end of 
the tape measure at    .

Through-
the-wall 
hole  65mm

Inside

Outside

Caulking

Wall embedded pipe 
(field supply)

Wall hole cover
(field supply)

Wall embedded pipe 
(field supply)

65

Содержание FTXS35K2V1B





















Отзывы: