background image

Si041252EE

Swing Motors

Removal Procedure

13

8. Swing Motors

Warning

Š

Be sure to wait for 10 minutes or more after turning off all power supplies before 
disassembling work.

Caution

Š

When reassembling, do not confuse the installing order of the 2 motors for horizontal 
blades and the colors of the connectors.
If you set the connectors or motors opposite, the horizontal blades do not move 
smoothly or noise may be heard.

Step

Procedure

Points

1. Remove the swing motor 

for vertical blades.

„

Lift the indoor unit with a 
wooden base for easy work.

„

Use the short screwdriver 
from the back.

1

Remove the screw 
behind the drain hose, 
and disconnect the 
drain hose.

2

Remove the screw at 
the rear, and remove 
the 2 screws on the 
right and the left side of 
the swing motors for 
horizontal blades.

3

Detach the pivot from 
the interlock shaft for 
vertical blades with a 
flat screwdriver to 
disconnect it from the 
swing motor unit.

„

Some models have fan 
guards.
Remove the fan guards 
beforehand.

Drain hose

(R10329)

(R21143)

Swing motor for 
horizontal blades

Screw

Screw

Interlock 
shaft

(R13092)

Vertical blade

Pivot

Содержание FTKS09JV2S























Отзывы: