background image

20

English

10-1 AIRFLOW SETTINGS WHEN THERMOSTAT IS OFF

Set the flow rate according to the requirement of the environment after consultation with the customer.
(As the factory setting, airflow for when cooler thermostat is off is set to SECOND CODE NO. “02”, while 
other settings are set to “01”.) 

(Refer to Table 6)

Table 6

 are the settings when shipped from the factory.

10-2 SETTING AIR FILTER SIGN

Remote controllers are equipped with liquid crystal display air filer signs to display the time to clean air fil-
ters.

Change the SECOND CODE NO. according to Table 7 depending on the amount of dirt or dust in the room.
(SECOND CODE NO. is factory set to “01” for air filter contamination-light.)
Explain to the customer that filters need to be cleaned periodically to prevent clogging, and the time that is 
set.

The periodical cleaning time for the filter can be shortened depending on the usage environment.

Table 7

10-3 SETTING AIR FLOW RATE INCREASE MODE

The set airflow rate (HH, H, and L) can be increased depending on the installation condition or customer’s 
request. In such a case, switch the SECOND CODE NO. as shown in Table 8.
(SECOND CODE NO. is factory set to “01” for standard.)

Table 8

Setting

Mode No.

FIRST 

CODE NO.

SECOND 

CODE NO.

Fan operation when thermo-

stat is OFF (Cooling/Heating)

Normal

11 (21)

2

01

Stop

02

Airflow rate when cooler ther-

mostat is OFF

LL airflow rate

12 (22)

6

01

Setting airflow rate

02

Airflow rate when heater 

thermostat is OFF

LL airflow rate

12 (22)

3

01

Setting airflow rate

02

Setting

Spacing time of display air 
filter sigh

Mode No.

FIRST 

CODE NO.

SECOND 

CODE NO.

Air filter 

contamination-light

Approx. 200 hrs.

10 (20)

0

01

Air filter

contamination-heavy

Approx. 100 hrs.

02

Setting

Mode No.

FIRST CODE NO.

SECOND CODE NO.

Standard

13(23)

0

01

Slightly increase

02

Increase

03

3P184443-9J_FM6.book  Page 20  Wednesday, December 14, 2011  10:29 AM

Содержание FAQ71CVEB































Отзывы: